Search results for query: *

  1. N

    Green bearings and axle seals question

    sounds good,will leave them, thanks all
  2. N

    Green bearings and axle seals question

    I have a 8 3/4 that has new axle seals installed near the flanges, also have green bearings that were already in the axles I picked up and they have a small rubber print type seal, should I pull the seals out of the housing, would it hurt to just run it with both seals?
  3. N

    Mild 340 8 3/4 gear and possibly converter question

    Its a 1973/74 904 trans i believe, the case is a 489, should have thrown that in there, also does the converter sound good/usable with this set up once gears are replaced to a 355 or 323?
  4. N

    Mild 340 8 3/4 gear and possibly converter question

    Have a mild 340 that has a 8 3/4 rear end, I have recently over the last year or two did a /6 to V8 swap into a 65 Valiant and recently got it back on the read. The Converter and 3rd member I basically ran because i had them already from picking up parts ect.. The gear is WAY to much, its a 5.13...
  5. N

    Only .5 to 3/4 play after drive shaft shortened

    QUESTION, after getting the drive shaft cut down, measured with wheels on ramps and weight in car so the suspension was at ride hight. Have read ideal play on the drive shaft is 1 inch, after cut down it more like half to 3/4 inch play. Q1- Is this a little to tight, and Q2 though about taking a...
  6. N

    [WANTED] Dodge truck prospector bed emblems

    Looking for a pair possibly 3 of the dodge prospector emblems, the ones that are on the sides of the beds with the pick and hammer, looking for driver quality, thanks
  7. N

    [WANTED] 1961 dodge phoenix trunk DODGE lettering/emblem

    Looking for 1961 dodge phoenix trunk DODGE lettering/emblem that runs across the center of the trunk lid under lock, may be the same as a dodge Polara
  8. N

    [WANTED] Small block 904 dust cover/converter cover

    Sounds good, do u take PayPal or Venmo
  9. N

    [WANTED] Small block 904 dust cover/converter cover

    Needing a dust cover for a small block 904 trans, shipped or in Jacksonville FL 32223, please let me know if you have one
  10. N

    Universal tube/fuel cell style 73/10 sending unit in new tank, auto meter fuel gauge

    Have tried a few after market sending units and gauge combos over the years with no luck. I have an auto meter pro comp fuel gauge and a new tank about to put in a 65 valiant. I picked up a fuel cell style universal 73/10 sending unit that I have made a flange for. Was going to weld some nuts on...
  11. N

    Early Abody Doug’s 450 header install BEFORE engine going in

    Doing a /6 to 340 swap in a 65 Valiant, have everything ready to go in the car.I know there are a lot of threads and great info about how to install these headers with the engine in the car. The engine is not in the car, steering columns is out, torsion bars are slid back. Wondering if anyone...
  12. N

    KH disk front 83/4 rear, prop valve and master cylinder brake line question

    thanks for all the info, I don’t think the metering block/prop combo I have from summit is adjustable, one question …looking at the later drum disk master cylinders, mine has a bolt on spring and boot, the newer models do not, should my rod work ok just removing everything but the rubber that...
  13. N

    KH disk front 83/4 rear, prop valve and master cylinder brake line question

    It will be a drum 83/4 rear and KH disks in the front, will check the wheel cylinder size in the read
  14. N

    KH disk front 83/4 rear, prop valve and master cylinder brake line question

    Long story shortish, have a 65 valiant, awhile ago had done the duel reservoir master where I ran the back res to the from drum distribution block, and the front res hardline straight to the rear rubber line. Was planning on doing the same but had seen a post where some recommended using a...
  15. N

    [WANTED] 1970 dart 340 clean scoop emblems

    Looking for clean 340 scoop emblems, kind that would come on a 70 dart with duel scoops, shipped to Jacksonville fl , thanks
  16. N

    64 Valiant light aqua armrest pads.

    Hit post to soon, but I dyed the black pads light blue metallic at matches pretty good
  17. N

    64 Valiant light aqua armrest pads.

    I bought new black ones several years ago (as at that time is was the only color reproduced at first) for my 65 Val in light blue mat. Company called herbs parts sold/sells dye in a can for early Mopar, it has held up pretty good,
  18. N

    1965 Valiant sedan vs hardtop interior/seat question

    Have a question, looking to buy new seat covers (front bucket bench rear) for a 65 Valiant. Classic and legendary list the back seat as hardtop rear. Called them and they said the rear seats are different from hard top to sedan, one has rounded corners on the base near the doors for leg and...
  19. N

    1965 Valiant sedan vs hardtop interior

    Have a question, looking to buy new seat covers (front bucket bench rear) for a 65 Valiant. Classic and legendary list the back seat as hardtop rear. Called them and they said the rear seats are different from hard top to sedan, one has rounded corners on the base near the doors for leg and...
  20. N

    Need help 65Valaint bench to bucket hole locations

    Didn’t think about that, just checked and there are dimples, even a extra hole in the brace near the door, thanks again,
  21. N

    Need help 65Valaint bench to bucket hole locations

    I have a 65 valiant bench seat car and putting 65 buckets in it with factory/stock seat mounts. Wanting to know if anyone can measure the factory holes on the floors with some reference points where the factory buckets seat holes are located. Even if I can get a good reference point for one hole...
  22. N

    [WANTED] looking for 64-66 a body V8 floor mount gas pedal assembly and throttle cable

    looking for 64-66 a body V8 floor mount gas pedal assembly and throttle cable in good shape, usually they have a white square piece of plastic that clips on the back, that’s rests on curved rod, looking for whole assembly and cable, thanks nick
  23. N

    Advice on sealer for insert after stripped water pump/timing cover bolt hole

    Have tapped the hole and cleaned it will acetone and q tips,
  24. N

    Advice on sealer for insert after stripped water pump/timing cover bolt hole

    Thanks all, no water in it currently, rebuilt it, started dripping on the run stand during break in, snugged it up and the stud pulled out of the block, now the oil pan off, balancer, timing chain etc... for one bolt lol
  25. N

    Advice on sealer for insert after stripped water pump/timing cover bolt hole

    Advice on sealer for insert after stripped water pump/timing cover bolt hole. Stripped one of the block through bolts near the water passage for the water pump. Have the hole drilled and tapped for EZ locks which went surprisingly very well. I usually use red rtv for threads in water jackets...
  26. N

    [WANTED] Small block 904 dip stick and tube

    Looking for a Small block 904 dip stick and tube, the the tan I have is 73/74 ish, thanks
  27. N

    Starting motor on stand wiring help

    Its an original 65 slant six valiant I have built the 340 for, few years ago I did the GM ingnition and GM coil conversion on the /6 and had been running it with that for the last few years. Recently I had tried to hook up the 340 the same way but could not get spark. Ended up using just the...
  28. N

    Starting motor on stand wiring help

    Yes, this will be just a one time, start it to break it in before install. It’s electronic distributor, resisted coil. Would hooking it up, neg battery to block, pos batt to starter, wire from small post on starter to tap POS battery post to engage starter/start, then pos battery to Pos terminal...
  29. N

    Starting motor on stand wiring help

    Figured this or the small block section may be best. Trying to start a small block (340) with electronic distributor and internally resisted coil on a run stand and can’t get spark. Wondering if anyone had a diagram or walk through in how to start a motor out of the car. Primarily electrical...
Back
Top