Search results for query: *

Going from a 2.74 gear to a 3.55 is there a chart to select the right Speedo gear for trans 4 speed o/d unit. Thanks

does anyone have std. rod bearings for a 1973 225 forged crank engine/ everyone around me has them on backorder or half a sets thanks

having a problem looking up slant parts, needed std. rod bearing for 1973 cast crank and pick up tube for a 73 /6 duster, the book only shows bearings for a forged crank , do the bearing interchange? it is the original engine thanks

I purchased a set of the Indy rebuilt cylinder a few years back for a 340 with the only thing done to them was the 2.02 intake /and 11/32 dia. stems the heads were the 974 casting so I've been on line looking for stock or ported heads with the same numbers for flow ratings I have found lots of...

does anyone know if the z bar bracket mount on the bell housing of a 78 f body od833 will fit a 73 abody. changing over from auto to 4 speed od unit. thanks

I don't need it, its free,needs to be gone this weekend. I have 4 timing covers with marks on the drivers side 1 f-body 8.25 axle housing with axles (no gears) 1 complete 8.25 for abody(gone) stock oil pans for smallblocks (gone) lots of misc.parts 1 727 rebuilt trans for smallblock/with deep...

well I'm moving to nc from md and need to clear out my garage so first is a 350 vortech engine ,uses in a dirt car the engine has 4bolt block std bore, steel crank, aftermarket cast heads with both intake bolt patterns, corvette baffled oilpan ,also 16lb manual flywheel need 500$ was running...

Well my 73 dusters in the body shop and I need to find the left lower quarter , I don't have a problem with the prices but the shipping cost is 70% of the purchase price ,all the company's are charging about $535 with the part only 285 to 325 and shipping from the west coast . So the question...

Four LBP stock wheels with 205/14 tires off a 73 duster and hubcaps in very good shape about 90%tire wear left .for 150$ LOCAL PICK UP ONLY

another how much hp will the 894 head make stock with 11/32 valves being the only mod with a raceing valve job on a stroked 416 with 9.5 compression and voodoo hyd .513/.527 cam with a eddy 340 single plane intake and 1 5/8 header ? is 410 hp possible? with a 750 quick fuel carb

good morning today I'm installing a camshaft in a 1975 318 stone stock engine, after collecting the parts I have 2 question's the lift is 470/274 dur. I planed on breaking in the cam with the stock springs then switching over to the higher pressure springs tomorrow. will the stock springs coil...

complete engine for sale in falling waters wva. out of 78 aspen,85,000miles ran good when pulled automatic. pm me for details $500.00.

I picked up a d150 today for the drive train 5.2 eng.1987 the last carbed one , can you tell if it has the roller cam/and good 302 heads with out pullimg off the valve covers, its all original just under 60,000 miles. thanks

I'm looking to replace the power steering box on my 73 duster with one rebuilt from a local parts supplier ,on my 78 aspen rt it had a very tight box with good road feel not like my duster, I looked up the rebuilder part # and they use the same part number for both boxes, so is there something...

team 5 elderbrock single plane 340 intake good shape no mods or milling $125 it is a TM-5 (Tarantula)

just finished a 416 sm block with 9.5 compression where do I start with spark plugs heat ranges for basic street driving /single plane/voodoo cam hyd.513/528. std mopar ign oranrge box?

just purchased 2 thunder carbs from elderbrock 500 cfms ,they charged me extra because they needed to be set up to run together .looking at the carbs I dont see anything done to them .anyone know what they did to them?

my car runs good but does anyone have a idea what the correct voltage should be at the coil + side with engine running ,with stock ign. I have 13.8v at the ballast pos side and only 9.6v on the wire to the coil if I unhook the + coil wire it will read about 1volt less battery voltage so is...

need drivers side door panel 1973 duster ,color is white or ivory I saw 1 on e-bay but it had a wood trim across the top .many thanks everyone

getting ready to switch engines in my 1965 cuda,someone told me there is a motor mount problem going from 273 to 340.has any body run into this problem( thanks):oops: