Anyone put a Holley Sniper on there 360? Bought my Little Red new in 79 and now thinking of replacing the Thermoquad with a fuel injection system. How difficult and expensive would this be to switch?
I have a set of spindles with the pin type calipers I brought years ago but can't remember what year they are to order rotors and pads. What years did A bodies use them or are they E bodies? I'm thinking I got those to up grade my different cars. Can anyone help to Identify these spindles.
New in box, never mounted, P4529725 M-1 single plane, Dominator flange fits 413, 426 and 440, Stage IV, V and stock heads. No longer available anywhere new. $350.00 pick up at my address or can bring to Chrysler Carlisle.
Holley 12R-8795B race carb, rebuilt less than a year ago, but never used. Comes with a 1 1/4" aluminum spacer. Asking 450.00, pick up my address or can bring to Chrysler Carlisle
Looking for at least two 15" wheels off an older "C" Body with disc brakes that takes a 9 3/4" dog dish hub cap. Need to be in good shape and not requiring tubes.
Trying to find the codes on the second line of the fender tag. The line is in all caps A to Z.
Just need codes for A=3, B=2 and C=3. I think it the engine size but not sure.
Has anyone moved the rad forward through the radiator support fame to get more clearance for electric fans? The car is a 68 dart big block 440 held in place with elephant ears. I need 3 1/2 " from the nose of the water pump to the back of the rad. Pics would help a lot. Ron
What preparation is needed for the AMD fenders to be painted? Is the black primer that the fender comes with OK to be sanded and painted or does it have to be completely removed then primed and painted?
Have a 540 cu.in. in an a-body with Indy max wedge heads. What header can I use that has no access problems to spark plugs. The headers I have now have has #7 and # 8 tubes exiting through the fender well. The #6 tube to head clearance will not accept a normal spark plug, maybe a shorty plug but...
Does anyone know the temperature range for Dot 5? My exhaust flange on the drivers side is less than 1/4" away from the proportioning valve. Will this cause brake problems on long drives?
Can anyone tell me anything about this distributor? Started engine with it and adjusted timing @ idle with a 508 cam about 1,000 rpm. Check timing @ 2,000 rpm, still the same, no advance. Should there be an advance? Ron
Having trouble finding a balancer. I got one from summit (Sum-163273) When compared to the original, the TDC cut was on the wrong side(drivers side). On talking to the tech at summit we ordered the Mopar Direction balancer (DCC-4452816). The TDC cut is the same as Summit drivers side). The 68...
Installed the Napa timing chain on our 68 dart 340. After it was installed it had at least a 1/4" play on each side. Has anyone else used this chain with the same play? What chain should I use?
Working on 68 dart 340 GTS. When installed the Napa 103228X the chain had at least a 1/4" play on both sides. I'm sure this Is not right. The motor is a 340 block dated 68. I need the correct timing chain. Can anyone help me with the right timing chain number?
I have a 540 stroker(440) in a 68 dart, the headers installed now have very little clearance on #5 and 6 cycl to install a plug and wire end. The header tube on these exit through the fender well. I want to use ceramic ends to protect the plug wire but don't have the room. They are 2" headers...
I have a 540 stroker(440) in a 68 dart, the headers installed now have very little clearance on #5 and 6 cycl to install a plug and wire end. The header tube on these exit through the fender well. I want to use ceramic ends to protect the plug wire but don't have the room. They are 2" headers...
According to my casting number this head was used 1964 thru 1967 on 361,383,413,and 426. Has 2.08 Int & 1.60 Exh. Can anyone tell me if I can use them on a stock 440 .030 over? And use all factory bolt ons. Thanks Ron
Anyone replace their points with the Pertronix conversion and how is it working? Seems like
a solution to upgrade and keep the stock look with no fire wall boxes or additional add on's. Any + or - with this system? Ron
My question for the 383 dist, does someone make a replacement plate that has a self contained ignition to put in the original distributor? Or does one have to buy a complete distributor and kit. And also which mini starter would work best for the big block 383. Trying to help a friend solve his...
Would it help or hurt the 400 by putting 2406516 heads the the engine. This casting number shows that the head has 2.08 Int and 1.60 Exh valves and is a closed chamber head. Used from 64 thur 67 on 361 - 383 - 413 - 426. The reason I'm asking is that I have a fresh set of heads that have been...
Picking up son's 68 340 from machine shop tomorrow! Was wondering what color paint the block was painted(I think red) and what product works best. We've been restoring his car for the last 20 yrs. Getting close to the finish line, wanna get it right.