Search results for query: *

My work truck started cutting out and almost back firing every time you floor it or accelerate fast.bi bypassed the ballast with a wire and the problem goes away. Bought a new ballast but no change. It acts like a lean out problem. Is not a carb problem. And like I saidbit doesn't do it when I...

I know its not an A-body but i need yalls advice. I might be trading for a 71 satellite wagon. It has a 318 4v and duel flow master exhaust. Solid body. Okay interior. Runs good. I have no clue on the value of these and was hoping you could help me out. Just want to make sure if I do it and...

I'm looking for a rolling tube chassis car or a back halved car. Finished or unfinished is fine. Looking for smaller and lighter cars/trucks but will consider others. Let me know what you have. Title is preferred, but not deal breaker. If a good deal I will buy with a bill of sale. So let's see...

I have a pair of new complete ready to bolt on magnum heads. I bought them for a project a few years ago and have no plans for them now. I'm building a bb and want to just sell these to put more cash towards the build. They are aftermarket castings. 1.92/1.60 valves. Heads look nice. Would...

I'm trying to put up a for sale add but I can't figure out how to upload my photos from my phone. I clicked on the attachment tab and it brought up the upload screen but I don't know where to go from there!! Please help!

Who sells the Siamese bore cast iron bb blocks? Any cons on these blocks? What HP levels will they hold? Are the finish bores precisely machined or should I get a rough bore then have it finished? I'm deciding if I want to just go this route instead of a factory block and I could go with a...

I'm getting ready to lay out the plans on the BB stroker build. This will be the first BB stroker for me. Will be going into a 3,000 lb chassis. Every one builds them from 451 on up. But which is really a better size for an all out race effort? Low deck 400 or RB 440 block? I know bigger is...

Ok my setup has been a barracuda race weight at 3450 lbs. Running a 360 with 10.3-1 comp , ported 596's with 2.02's Holley strip dominator single plane with an AED 750hp DP carb. Hughes solid cam 248° 252° @ .050 .563 .572 lift Ran 727 and turbo action S800 street 3500 stall and 3.91 sure...

Sorry I can't say or even hint what I'm talking about until the prototype is made and patent it. But, I will let you know that it will be a desired item on practically any engine combo from completely stock to a full blown 8 sec drag car small block to big block. And if you reply to this with...

I am wanting to build a flow bench. Has anyone built one? I'm looking into this kit alsohttp://www.flowperformance.com/system.html

Kinda a general question on the HP and TQ gain from 10.1 comp to 11.1 comp. How much will it really gain? Based on Iron headed sb.

OK here is the setup 67 notch weight 3300lbs Chassis STK ft shocks with /6 tors. STK rear shocks, /6 leafs with extra leafs added. NO snubber or traction bars. B body 8 3/4 with 3.91 sure grip 360 .030 10/10 STK crank Eagle sir rods KB 107 pistons .005 positive deck. Out of hole 587...

ok spec on setup. 360 .030 kb pistons 10.2to1 comp. run 93/110 oct 50/50 mix J heads ported with 2.02/1.60 hughes engines cam HTL4852s solid cam. 248 252 @ .050 .563/.572 106 lsa. air gap intake,Hooker super comp headers, carter race mec. fuel pump, holley street avenger 770 carb , pertonics...

ok spec on setup. 360 .030 kb pistons 10.2to1 comp. run 93/110 oct 50/50 mix J heads ported with 2.02/1.60 hughes engines cam HTL4852s solid cam. 248 252 @ .050 .563/.572 106 lsa. air gap intake,Hooker super comp headers, carter race mec. fuel pump, holley street avenger 770 carb , pertonics...

I had a set of comp 821-16 solid lifters laying in the shop that I was going to use. These lifters do not have a oil groove cut in them. Will these work? Or will it block off the oil in the gallery ? These look very heavy and I might just get some with the direct lube, but just curious thanks.

What's the safe maximum amount you can cut the spring pads on 596 heads? I need to cut .050 to get my installed heights right with a valve length of 5.00. Will this be ok? Still would like to know max about cut for future knowledge . Thanks

This will be a everyday driver. Just curious on what numbers to expect from this simple build from parts I had in the shop. Stock rebuilt 5.9 short block stock pistons stock rods&crank Mopar .028 head gaskets new magnum heads with bowl blend short turn radius and slight runner clean up...

I have a magnum 5.9 im wanting to run my 230/.480 hyd flat tap cam in. I know about getting new push rods and oil through lifters and need to cut the guides down for retainer to seal clearance , but what valve springs do I need that will fit? There has been many build ups using these heads and...

I have a intake I ran a few years back on my 383 in my 69 coronet that I want to sell. Its a edelbrock DP4B . In used shape. Needs cleaned up. Has plenum divider milled out. Asking $100 or best offer. + shipping. Located in east Tennessee

This is a unused weiand aluminum intake. Is dirty and needs cleaned. Was bolted to engine and left outside so it got dirty but was never ran. In good shape no corrosion or damage just dirty. Asking $100 obo + shipping . Located in east Tennessee

This is a set of BB Crane rocker arms. They are used with around 4k miles on them. Asking $200 for them Plus shipping . Located in east Tennessee

I hate to sell but went through divorce and need cash badly! I have a 1971 318 short block bored .030 with torque plates,aligned honed, and deck squared. Has a steel crank turned .010/.010. rods have been resized and are bushed pin type . Keith black 167 hyper pistons with file fit rings to...

I have a set of 596's fully ported with 2.02 1.60's ok original plan was running a fairly healthy solid cam,but right now I need to run a small hyd lunati cam 230/.480 im using a set of bb springs with installed height of 1.8 and diameter of 1.5. My solid lift dual springs were set at that...