Search results for query: *

I like to light the models. This is the second one I have done. LED bulbs, button batteries and switches.

I am looking for two screws for the headlight door on my '64 Barracuda. Can't find them anywhere. (Phillips head) Please advise........... Thanks Dave

I planned on putting back in the old in line glass fuel filter. I've got the filter cleaned beautifully. What I didn't count on was the difficulty finding the filter element. The old (dead) filter is a Fram CG6. Any ideas on where to find one? I've just about exhausted any searching on line...

Need some advise please. Specs., 1964 Barracuda.......273 V8........manual brakes, stock. Replaced the master cylinder with stock manual brake master. This leaked, between the master and the firewall. (Did a nice job on the fresh paint too, but...... Replaced it again. leaked the...

I purchased weatherstripping for my 1964/5 Barracuda and am comfused by the quarter window seal. The seal on the left is the original, the one on the right is the new seal. Am I missing something? Looking at this backwards / upside down? This doesn't seem like it will work. The people I...

This kit from Atlas Obsolete Chrysler Parts? http://stores.atlaschrys.com/-strse-595/1964-1965-1966-plymouth/Detail.bok It's the entire cars' worth of weather stripping. (Which I need) Just need to know if any one has experience with this kit as it's quite pricey. Need to be sure...

Frustrated.... I'm looking for something as simple as black foam, or so I thought. 1964 Barracuda. The Chrome strip that goes above both side windows with the rubber weather strip to seal the windows when they are closed. Well, there is a strip of black foam type stuff that is glued to...

1964/65 Barracuda I have read that using Gojo will soften the rubber on these gaskets. So I went to Napa to buy a small bottle and see. As it turned out, because I chose to get the bottle without the pumice, and not read the bottle, I ended up using Napa brand. The gasket is softer. Much...

I've searched as well as posted the question before and can't seem to get any answers. I have a 65 Barracuda body that I need all the weather stripping for from cat whiskers to the colored windlace. I'm guessing that any of you who have done a restoration on these cars had to replace the same...

Yes, again! I know this has been asked at least 5 million times. Well, here I go again. I NEED HELP! 1964 Barracuda.....all the rubber trim. Roof line molding, window seals, cat whiskers, belt line molding, etc. I need it all. I keep reading horror stories of this one who got it from...

As I have been working on my 64 A body for too many years to admit.... I should have around 235 to 250 hp out of my 273 V8. That alone is exciting. However, .... yesterday I put a deposit down on (soon to be my) 2010 Plum Crazy SRT8 Challenger! Now I'm excited! :supz:

Time to go to the PROS!! I can't seem to figure this one out. Just reinstalled the dash. New wire loom. All plugged in. New fuses in the new fuse box. And........the radio doesn't work!! This is the stock AM radio in my 1964 Barracuda. It worked before the tear down. (Too many years...

I need to replace the defroster vent tubes in my 1964, non air conditioned Barracuda. The old ones are brittle, torn, etc. I know yours had to be the same way. Where did you get yours from. The original vents in the dash, (which I'm using), where the hose attaches, are 2 1/2" outside...

The questions here are, should I re-use the windshield and rear window gaskets on my '64 Barrucuda or buy new. If I should re-use the old, how do I "make them new" again. If I should buy new, who has the best product? Thanks, Dave

I know I saw the answer somewhere here before, but I just can't find it. I'm looking for the windshield wiper gasket that keeps the cowl from leaking through the wiper holes for my '64 Plymouth Barracuda. Can't find them anywhere. Any help appreciated. Thanks, Dave

Iv'e got a 1964 Barracuda. Right now I've got 14" stock wheels on it while I cleaned up the original 13" wheels. (Going for the original look) The tires on her now are H78-14. That's right, they are still holding air!! In any case I really like the look. If I convert to current size, they are...

Desperately seeking NOS or good as NOS headlight doors for my 1964 Plymouth Barracuda. Email @ [email protected] THANX Dave

I put a new master cylander in my 64 Barracuda. Bench bled....bled the system etc. Time goes by, I notice the fresh piant bubbling below the master cylander! It leaked from behind the master, between the firewall and the master....I can't figure out why! Dave

64 barracuda wing window. The chrome piece on the bottom of the window, with the pin and handle, how does that come off? I want to send them out to be re-chromed Thanks, Dave

I just wanted to take the time to say THANKS!!! This is an amazing site. The people here, the info here, the help here etc... Thanks to the creators, the maintainers and all who help. :cheers: Dave

I have been looking for these rocker panel clips for my '64 Barracuda and just cant find them. I need 20. Any help is appreciated!! Thanks, Dave

As I've been having problems aligning and realigning my hood, it turns out that the body man never put the clips back on that hold the hood brackets to the body. Both sides (brackets) came off the pins. I finally got the brackets back on the pins but I am having huge problems trying to get the...

Only because I saw a picture of this (and the other side) did I find out that this is a support bracket from the engine on my '64 Barracuda to the bellhousing. However since these were not installed when the exhaust was put on, (custom duals) I can not put the passenger side on. The drivers side...

Seems like a simple question... how do I remove the plastic pins inside the plastic rocker molding clips on my 64 Barracuda? Thanks Dave

Another how to... How do I seperate the seat back from the seat on my 64 Barracuda Bucket seats? Thanks, Dave

I'm guessing this question has been asked before and will probably be asked many more times. But... I'm going to be installing the front and rear windows in my 64 Barracuda. Question...What goes between the body and the rubber seal, and between the rubber seal and the glass? Is there...

I am looking (searching everywhere) for the rubber gasket that goes between the tail light assembly and the body on my 1964 Barracuda. Any suggestions?

OK you purveyors of all knowledge. I am befuddled! My 1964 Barracuda (273) has been down for the count for three and a half years. (At the body man's place) Prior to going, she ran like a champ. Now that she's back; after changing the oil to get the oil back to the top of the engine, I actually...

OK now that I've finally got the car back and have had the opportunity to start putting her back together...here come the questions! As I'm preparing to re-install the wing window assembly I see that most of the metal is stainless. Except for one side of the "triangle" on the 'outside'. Of...

Is there any one out there that knows of someone in the Chicagoland area that will make a house call to remove the headliner from my donor car and re-install it in the finished product? Thanks!! Dave