Search results for query: *

Looking for anyone with experience with the Pypes Turbo Pro. Here's my story: 73 Dart Sport, built 340, 200-4R trans, 3.91 Sure grip. Summit 2.5 exhaust with H pipe. The Summit turbo mufflers sounded great from outside but drone was terrible. Went with Dynomax Super Turbos because they were...

Vehicle is a 73 Sport 340 with the 200-4R transmission. Just finishing my restoration. Looking at adjusting the TV cable. Videos on YouTube all have slightly different methods. Some say extend the cable fully, open the linkage to WOT, and that's where the cable attaches. Others say to seat the...

Looking for the driver's side interior door latch assy for a '73 Sport. Spring is missing on mine.

One pair of upper control arms off of 73 Sport. New big ball joints, new PST poly bushings. Will need one boot. $90.00 shipped in lower 48.

May have been covered before, but couldn't find it. Just installed a set of QA1 upper arms purchased from a member on my 73 Sport. I really like them but have a question. Should I ever need to replace the ball joint, what tool do I use? I have the special socket that PST sells and I used it on...

One set of Smith Brothers pushrods, brand new, never used. 5/16 diameter, 5/32 radius, 7.742 in. long, ball / ball ends. Bought these to use with the B3 Racing geometry correction kit on my 340. Went with a different cam and don't need these. $80.00 plus shipping.

One set of Smith Brothers pushrods, brand new, never used. 5/16 diameter, 5/32 radius, 7.742 in. long, ball / ball ends. Bought these to use with the B3 Racing geometry correction kit on my 340. Went with a different cam and don't need these. $90.00 plus shipping.

I have a set of new Crane 99278 anti-pump lifters for an LA small block. Decided to go with a solid cam. These were installed in the short block but removed before engine was installed or fired. $75.00 shipped in the lower 48.

73 Dart Sport, 340, fresh 8.25 rear with Motive 3.91 gears and a Sure Grip. Part of a 4 year restoration. When driving I get a steady whine from the rear. Whine speeds up and slows down with vehicle speed. Did not hear anything with a stethoscope on the housing and the car in gear. Pulled the...

Just got a NOS middle housing for the engine side of my bulkhead connector. 1973 Dart Sport. The old housing had some kind of insulation/gasket pressed down around the male terminals. Anything special I should use to replace it? I thought about some thin foam insulation, like goes in the heater...

My 73 Sport was a factory AC car. As part of my build I'm replacing the underhood pieces. Have a Sanden compressor and new condenser and dryer. My question concerns the hoses. On the stock setup, the hose from the small firewall connection to the dryer was a piece of formed metal tubing. I can...

Vehicle is a 1973 Dart 340 Sport, finishing up a 4 year build. I fried the fusible link on the black wire coming out of my bulkhead connector under the hood. It was a stupid mistake and I won't embarrass myself by explaining. I'll just say it involved installing a new starter relay. And I've...

Vehicle is a 73 Sport. Need the plastic collar that mounts behind the window crank.

Installing the new carpet in my 73 Sport. The carpet is molded, from ACC, but the molding is not perfect, as I expected. Question is, can I use a heat gun or blow dryer to heat up a couple of the corners in the rear floor pan where it bunches up and reform it to fit? If so, any special technique...

In the home stretch with my 73 Sport resto. Photo is the repainted metal trim that goes above the doors. Removed 4 years ago and now I don't remember what those notches are for. Any help is much appreciated.

Finishing up the SEM paint on my 73 Sport interior plastic trim. Turning out great, going from parchment to black. My question before I try and maybe mess it up. The headliner trim above the door is metal. Can I use the same SEM color coat paint on these pieces? Or do I need to find a standard...

Need a license plate light holder in very good condition for a 73 Sport. This is the one with 3 bolt holes.

These pieces came with my exterior gasket set. I know they're for the rear bumper but not sure how they attach - 73 Sport. Any pics or description? The FSM did not help.

Thought I'd post this for anyone considering the Classic Industries cardboard glove box for A bodies. My '73 Sport project did not have a glove box. I'm at the point on the interior where I'm ready to install one and ordered it from Classic. My car is a factory AC, don't know if it matters or...

Looking for a set of front bumper brackets from a non-shock 74 Dart, Sport, Duster. My 73 Sport bumper is toast and I have a new, show chrome plated front bumper from a 74. Would prefer not to rework my mounts if possible. Just need the brackets, not the long bar that runs the length of the bumper.

Can anyone tell me if glove box doors / hinges were different for various year Darts / Sports around the 70 - 75 time frame? Trying to get a door to fit my 73 Sport. Door was purchased from a member as a 73 but now not so sure. I watched the video on an earlier post and my hinge is on just like...

Anyone know the knurl diameter of the stock 8 1/4 wheel studs with drum brakes? Have to get longer studs to move my Vision wheels out toward the fenders. Thanks FABO.

One pair of sun visor arms. Excellent condition. Not sure what they came off of, but the arms are 9 inches long. $30.00 shipped in the lower 48.

I have 6 rear arm rests with ashtrays $10 each. 5 bases, $5 each. Plus shipping. Came from 73 Sport, not sure what else they will fit.

One set of Smith Brothers pushrods, brand new, never used. 5/16 diameter, 5/32 radius, 7.742 in. long, ball / ball ends. Bought these to use with the B3 Racing geometry correction kit on my 340. Went with a different cam and don't need these. $100.00 plus shipping.

Front bumper with bumperettes for a 74 Sport. Not sure if it fits anything else. Very good driver quality. Light rust on bottom center. Too big and expensive to mess with shipping. Pick up in SE Virginia. $75.00.

The Dart (73 Sport) will be back from paint next week and I'm getting the interior pieces together. Can anyone ID these two? They're about 11 1/2 inches long and I marked them passenger and driver. Since it's been 4 years since I removed them, I can't remember where they go. Thanks guys!

Need two of the plastic pieces that go on the seat back release for a 73 Sport with bucket seats.

Passenger fender from 73 Dart Sport. Very nice but has some body filler in top headlight area, no other rust. Small dent above wheel well. Too big to mess with shipping. If you need a patch you can have it for the cost of shipping, or pick up the whole piece in 23061 zip.

I have a set of new Crane 99278 anti-pump lifters for an LA small block. Decided to go with a solid cam. These were installed in the short block but removed before engine was installed or fired. $75.00 shipped in the lower 48.