Search results for query: *

I have a 66 Cuda with a 360. CompCam 280 Magnum cam and 9.5 compression. The 3310 runs rich(plugs are black) with stock from Holley 3310. The Holley 600 1850 carb on it runs great(plugs not rich) but low on top end power. I would like to run the 3310 for better power. What jets and tuning have...

I clear coated my aluminum manifold with aerosol clear spray. Now it is turning yellow. I would like to paint mopar engine red color. How do I prep intake for painting without removing from engine. It was very difficult to install. The intake is edelbrock airgap on 360 in 66 barracuda...

I'm converting to disc brakes on 66 Barracuda using 75 dart slider disc setup. What size rims and tires did you use for this swap? Looking to replace present 195/70/14 (sbp)with larger tires that will fit the new setup(bbp). I have 15"/5.5 Ralley, 14"/6.0 Ralley and American Racing Outlaw 15"/7...

I'm converting to disc brakes on 66 Barracuda using 75 dart slider disc setup. What size rims and tires did you use? Looking to replace present 195/70/14 with larger tires that will fit the new setup. I have 15"/5.5 Ralley, 14"/6.0 Ralley and American Racing Outlaw 15"/7 available. Trying to...

I've looked at many articles for early disc swap and have some questions. 1. Car is 1966 barracuda V8(360) with 10" drums all around with dual M/C conversion 2. Parts are from 1975 dart 6cy. with manual disc brakes(1 piston slider) 3. I know upper control arm is replaced(big ball joint) and 75...

The Mopar Action website is gone. Can someone post it so myself and others can make a copy. Thanks

Is Mopar Muscle(Harris Publications) magazine stopping publication of the magazine?

OK, I took car apart to be painted and now need to connect every thing back. I need to know which bulbs go where in rear tail light assembly. There are 3 sections Top, middle and bottom of tail light. Please give me function of each. ex. stop, directional, backup etc. Thanks :oops:

I have a 66 Cuda with dual M/C installed (non-power). What is best way to replace M/C? Remove mounting bolts and pull M/C from pushrod or disconnect pushrod from brake pedal linkage and remove M/C and pushrod together. Thanks

I have a 66 Cuda with dual M/C installed (non-power). What is best way to replace? Remove mounting bolts and pull M/C from pushrod or disconnect pushrod from brake pedal and remove M/C and pushrod together. Thanks

Looking for picture of 66 Barracuda grille(chrome sides) that shows how grilles are detailed to restore my grilles. interested in the painted areas of grille. Thanks

Looking for picture of 66 Barracuda grille(chrome sides) that shows how grilles are detailed to restore my grilles. interested in the painted areas of grille. Thanks

My 66 Barracuda with 360 was running a little bad so I decided to pull the plugs and see what was going on. All plugs (autolite 65) looked good except #3. It was oil foulded. Checked plug for resistance, was OK. Checked spark plug wire for resistance,OK. What do I check to find problem? :???:

66 Barracuda 10" drum brakes. When you apply brakes easy it pulls to the left. If you apply brakes hard it will stop straight. What is wrong with this car?? Thanks :smile:

Please post picture of colors on 66 barracuda rear window trim emblem Thanks

what do I use to prep and paint that center emblem on the rear chrome window trim of 66 Barracuda? Thanks

what do I use to prep and paint that center emblem on the rear chrome window trim of 66 Barracuda? Thanks:glasses7:

Will 245/60-15 fit on rear of 66 Barracuda? 8 3/4 lbp rear Thanks

Will 245/60-15 fit on rear. 8 3/4 lbp rear Thanks

How would you clean dash pad so it can be dyed a new color. Thanks

I was reading an article in Mopar Action Feb.2013 on tuning MP ignition called Cal TEch. It goes on to say that MP distrib. build after 2000 are virtually impossible to setup to run correctly. Has anyone had a problem with this MP ignition system build after 2000? What was your solution or setup...

Looking for info and picture of correct dog dish caps for 66 Barracuda? With or without Plymouth on cap? Thanks

I'm going to use relays for my headlights. The factory harness uses a wire that goes from left to right headlight(series) to the radiator support. How should I ground the headlights using the relay setup. I'm using 12awg wire to connect to the headlights. The car is a 66 Cuda with 2 lights...

I want to make the Allpar.com mod to the alt. that runs a new bat wire(alt) to the starter relay batt terminal. This allows the alt to charge directly to the batt and takes some stress off the bulkhead connector. The car is a 66 Cuda. I don't know what the alt output is. It looks like a mopar...

Does anyone have the specs for the vacuum advance canister for this MSD 8388 distr(ready to run 273-360). Looking for hg to start advance and what is full advance spec deg/hg when all in?

What is driveshaft length for 66 barracuda with 360/904/8.75? Thanks

I'm looking for a picture of Hood to radiator support installation for 66 barracuda. Seal came with no picture or directions. Thanks

I have a 66 Barracuda that had pin stripes along the body lines front to back. I had the car painted and would like to have the pin stripes put back on. Does anyone have the location and size of the stripes to put back on. Close up pictures and dimensions would be great...

What air pressure would you put in 195/70-14 and 215/60-14 on 66barracuda and 360 Thanks

Do you need to remove windshield to remove the whole dash on a 66 Barracuda? What is involved? Thanks