Search results for query: *

Hi Folks My 1971 bucket seat tracks need to be refurbished. They work good, but are a little dirty and have a little surface rust. I would like to clean, paint and lube them before installation. Do they need to be disassembled to do this, or can they be done as a unit. Thanks FABO.

Hi Folks I'm having a check engine light issue on my 1999 Toyota Camry 2.2l engine. The code comes back as an insufficient EGR flow fault. I have checked and tested the EGR valve, Vacuum modulator, Vacuum switching valve and all related hoses. All check out, and test fine. Here's the...

Hi Folks 1970 Swinger with 10 inch front drums. One of the steering knuckles has one threaded hole for the ball joint attachment. The other knuckle has no threads in either of the ball joint mounting holes. Is this normal, or have the threads been drilled out? Are they junk? Thanks

Hi Folks The facts.......... Fresh 340 (with about 2hrs run stand time) with 9.3 CR, running a Comp XE262 cam. OEM intake with a 1972 TQ. Base timing 20* btdc (MP gold shaft distributor.) Engine installed on a run stand, all warmed up.............. Smooth idle at 850 rpm pulling just under...

LOL, I read all the rants about shipping, and here is another.......... A RockAuto purchase shipped to Ontario Canada from Tonawanda NY via Memphis :BangHead: It's been sitting there since the 14th, as my car sits on the hoist waiting on parts. At least I'm saving $40 bucks from buying...

Hi Folks NON-MOPAR........I've got a 1999 Toyota Camry and started hearing a light growl in the front while taking a swooping right curve on an off ramp. I can feel it slightly in my accelerator foot. I'm thinking Driver side wheel bearing, what do you think? Growl goes away when I take...

Hi folks Trying to determine tire sizes. I have a set of 7 inch wide slotted mags with 3 1/4 back spacing. I am considering using 215's all around since the originals would be slightly shorter with 205's. Does anyone have a straight on side profile of their Demon with 215's? Thanks FABO

Hi Folks The pics are all over the place when I look the application up (Rock auto, Classic industries etc.). The crappy hose that came with the car (in a box)looks like a '73 model With Chrysler pump so I am not sure what to buy. Any help would be appreciated. Thanks FABO

Hi Folks Here is a photo of a Light Gunmetal 1971 Demon that my friend built (RIP Randy). If you are from the west coast of Canada you probably recognize the car. I am painting my 1971 Demon the same Light Gunmetal and will have the same hood treatment with the exception of my scoops being...

Hi Folks Has anyone removed paint over-spray from a plastic tail light lens before? I don't want to risk scratching it with something too abrasive, or melting/hazing it with too harsh of a chemical. Real world experience please. Edit: Demon lenses. Thanks FABO

Hi Folks I kept looking at this, and I just don't get it? I don't see a problem :)

Hi Folks So I have these Cal 500 vintage slots with a 4 inch bolt circle. As you can see by the pics, the center caps that I bought encroach the wheel stud holes so using them is a no go. I really don't like the look with the centers open to the hubs and am seeking a solution......Perhaps...

Hi Folks I know I've read it somewhere before, but which forum member(s) supply TTI exhaust components. Looking to get something shipped to Canada. Thanks FABO

Hi Folks Running a 340 auto with an XE262 cam, 1969 HP manifolds and a factory TQ on a 1971 Demon (3.23 gears). Looking to purchase a 2 1/2 TTI exhaust and see that there is an X option and an H option for crossovers. I am looking for something with no drone on the highway, and not...

Hi Folks Finally one colour. First coat of high build. Getting closer to the finish line!

Hi Folks I have a 3 speed manual transmission with bell housing, clutch, pressure plate and flywheel from a 1971 318 Demon. I also have a 4 speed manual transmission with bell housing, clutch, pressure plate and flywheel from a 1970 340 Swinger. My question........Will all of these parts play...

Hi Folks I have a '71 340 Demon with the M6X9 interior decor option. Description calls for charcoal upper door frame paint, but mine just looks flat as opposed to the charcoal colour that you'd see on the bucket seat inserts. Does anyone have a picture of the original charcoal upper door...

Hi Folks Looking to get hold of @challengergary re: Demon stripes. Please PM me Gary, your in box is full. Thanks

Geez, these things are taking over :rofl:

Hi Folks The "Report" button works great. I was contacted by a "New Member" with an E-Mail address for a Wanted thread I posted. I reported it, and within a few minutes......Gone. Be careful out there guys and gals. Thanks for doing a great job Mods:thumbsup:

Hi Folks Looking for a fuel sock for my 5/16 OEM fuel sender. I see 521 has them listed, but they are in Colorado, and the last thing I bought from that area went through California and got caught in a 6 week loop LOL. Summit has them listed, but the only store that ships to Canada is in...

Hi Folks Electrical or Fuel & Air? Here goes........ :) Does anyone have any personal experience soaking a complete fuel sending unit in Evapo-rust? I know the metal can handle it, but what about the rheostat winding? ALSO............Does anyone have a link to a pick-up sock for the...

Hi Folks Can anyone advise how much I could expect to pay to have 2 motor mounts, and a complete transmission mount/cross member media blasted and powder coated semi gloss black. Contemplating just using Rustoleum. Thanks FABO

Hi Folks Well, I finally broke in my fresh 1971 340 build after 4 months. This engine is going into my Cruiser 1971 340 Demon this spring (hopefully). Here's the rundown on the build........ .040 Cast Silvolite pistons .018 out of the hole. Piston clearance .00075 Hastings moly rings...

Hi Folks I bought a Mopar distributor that is supposed to have a performance curve. The mech. advance doesn't start until 2000 engine RPM and by 2500 it has only picked up 5*.......I stopped there! The weights move freely, but the springs look a little heavy. Any ideas as to what application...

Hi Folks Getting ready to break in a fresh 340. I have to fill the cooling system, and in the past I have experienced the odd air lock in other engines. What is the best procedure to fill it with 50/50 and be able to crank it to 2000 RPM for 20 minutes immediately after starting? Looking for a...

Hi Folks Still playing around with my "mule" 318 getting Fuel and ignition straightened out before I break in the 340. Today, I ran my Mopar Performance distributor (bronze internals). Here's what I found......... Advancing began at approx 1500rpm. By 1600, I was at 5*, by 1800 at 10*, and...

Hi Folks Does anyone have a link for those rubber engine mounts that have an internal metal locking system integrated? Trying to avoid a torque strap. Thanks

Hi Folks Not sure if this is normal............. I ran my TQ on a run stand and it performed great. When I removed it from the engine the following day, I noticed gasoline on both sides of the plenum floor of the intake (old school performer). I am not sure if it was there from running the...

Hi Folks So I have a 1971 318 set up on my run stand with a 6139 Thermoquad. I rebuilt the carb, and adjusted it. On my stand, it purrs like a kitten at 690 RPM and 20 inches of Vacuum. Carb and engine adjustments are as follows..... Air mixture screws 2 1/2 turns out Idle timing 10* BTDC...