Search results for query: *

Aloha, We are in the process of freshing up a 360 for my son's Dart and ran into a weird problem - it appears that we have a small water leak from the passenger (side in the vicinity of the where the Alternator bolts in. It is not the bolts - tripled checked and used thread sealer on them. Is...

We have a 360 in a 68 Dart that was originally a slant 6 car. We used a 71 Dart swinger K frame and some engine mounts we bought from O'Reillys but had to use some washers to get them to work. Engine also seems to sit low and centerlink clearance is marginal. My question is this - is there a...

What has everyone had luck with while sealing their water pump? just gasket and torque? or do you use rtv? Thanks - SCRAG

I snapped a rusted bolt in the engine block....I snapped only a few threads I believe off of one of the two long bolts that crank down the water pump. How long are these bolts usually? Is there anyway I can bypass taking it out since I am trying to avoid having to take off the timing chain...

My engine hesitates when I accelerate too fast such as the pedal to the floor practically. It just putters like its kinda getting too much or too little amount of gas, a buddy of mine said that he thinks I'm runnin' a little rich. I'm a young gun and havn't grasped the mehod of tuning my carb...

I wanted to repaint my 68' Dart 270 grill because the black is fading, and wanted to know if there was a specific black that was used. Due to the fading the black looks like it was a flat black, Thanks for the input ALOHA, SCRAG

My column shift is very loose and can slip into gears or out of gears. Is there any way i can tighten it up or access it. I've removed the steering wheel and removed mostly everything. Thanks.

Can we use Drum brakes, backing plates from an E Body 8.75 rear end? I am replace my 8.75 with a Dana and wanted to pull these and the the center chunk 489 with 3.23 Limited Slip for my sons Dart. I know I have to get new axles but just having these parts will be great...

We swapped a 71 K frame from a Dart 318 powered car into a 68 Dart that had a slant 6 in it. Bought a 360 (78 engine) and put it in and from all appearances it looks like it is sitting too low - we have been told this as well. We are getting some header scrapes and the fan is rubbing on the...

Does anyone have any other radio ideas other than the glovebox or under the seat....more like somewhere under the dash. Please post your opinions. my goal is to not make a single cut in my dash and will try anything not too. Thanks.

Hey everyone, Well my sons 68' dart recently leaked gasoline.......question is why? Well we looked for the source and found there are not holes and are no rust spots so no help there, but we found it was instead coming from the sending unit area. From what it seems the gasket either was not on...

how do remove a 68 dart steering wheel? i've got the middle piece off but cannot get the horn piece off thats the triangle piece and i have already unscrewed the center nut....am i missing anything? My puller cannot reach the wheel itself and caan only rest on the horn piece but if i do so it...

This is going on a 68' Dart that my son has, swapping the darts blue steering wheel (kinda worn) for my old original cuda steering wheel (looks like a wooden steering wheel) and is heavier, my son says he loves the look and i'm not using it anymore. YOUR OPINIONS PLEASE ( I know that its what...

I am trying to order parts to do the brakes on a 68 Dart. It is drum's on all 4 corners with 9 up front and 10 in the bake. I saw specs on 2 different bore sizes and I am trying to decide either how to measure them or which one to go with. Thanks

Aloha, We are slowly making progress on our Dart - Father Son project - we are installing a 360 into a 1968 Dart 270. Swapped out the K frames, engine and 904 is installed. Finished wiring the electronic ignition and have been struggling with the pulleys. I finally got a hold of a matching...

Aloha, We are swapping a 360 into a 1968 Dart. We are dropping the K Frames today and swapping them when I noticed that there was a difference in the shape and size of the V8 to the Slant 6 (with regards to the Idler and steering arms). We are running headers so this is a concern whether...

We just bought a 68 Dart with a 225 and a single barrel holley on it - our issue is that as we were trying to get it to run we poured gas into the top of the carb and saw gas leak out of 2 small openings in the main body of the carb - just above the base plate - where the gas dribbled out and...

We found a garage stored 1968 Dodge Dart 270 with 225 and column shift owned literally by a little old lady who is looking to sell - interior is good solid metal overall light bubbling of the paint on the rear quarter - looks more surface than anything major. Car runs - title/plates in storage...

I was wondering if anyone knew of a refurbish or rebuild kit (including weather stripping) for a sunroof on a 73 dart. Thanks

We just picked up 1973 Dart Swinger with a factory sunroof - so far everyone seems to think that was pretty unusual and upped the cars cool factor for my son. Car currently has a slant six, 904 transmission - runs no issues and my son is driving the car to school. It also has drum brakes on...

I decoded a Fender Tag and was wondering about some of the "options". Also does anyone know about the Export dusters (read the fender tag break down). VS29: Plymouth Valiant,Duster Special 2 Door Sports Hardtop H08: 340 275HP 1-4BBL 8 CYL 1970 Export XXXXXX: Sequence number E55: 340 cid 4...

Here is the EIN off of our /6. 7225R 7 7 2E

Considering a 360 Magnum motor - what is a the additional issues of using this motor vs a 340 or 360? Looking at Motor mounts, 727 (additional costs that can bite me in the ***) Thanks Scott

I looked at Goodmark, Padock and Year One. Did not see them. Are they made at all? I know guys on the mainland can find these at swap meets and at salvage yards but not here in Hawaii - at least so far. Anyone with a pair (no pun intended) that might want to ship them? Thanks

I have a 70 Duster that I am currently trying to swap a 360 in - eventually. I have a 71 Dart Swinger for a parts car and my plan is to swap the K frames from the 318 V8 powered Dart with the 225 /6 powered Duster. Should I swap the steering pieces as well between the 2 or can I swap just the...

I found some rims for my sons Duster they are 15 x7.5 and 15 x 8.5 with 4 inch back spacing and are unilug rims (fit both bolt patterns). Not a big fan of unilugs but this gets our 15inch rims for his car. Now the question - Will they Fit for a 1970 Duster??????? Thanks in advance.....

First post - your site was recomended to me by a fellow Mopar's Hawaii member. I hve a 1970 Cuda and am in the process of doing a father and son project with a 1970 Duster. The Duster is a 6 cyl car and we plan to put a 360 in it. I also have a 71 Dart Swinger that we are using as a parts car.