Search results for query: *

You probably have casting 2206324 and not 342,this is a 61-62 casting only and has 2.08 intake and 1.60 exhaust valves,mrmopartech

If any one needs heads in Canada,Ontario,Quebec,or the upper north east,I have some 30sets of small block and mostly big block heads,426 hemi heads and old hemi heads from the 40 and 50s,. Heads are only as good as the cam being used to work the heads.Its of no use to buy a head that goes to...

I would go with the holley 600 V/S carb and have it jetted and drilled to for motor to get the power and the mileage,or smileage,mrmopartech

Most holleys and carter carbs have vacum port tubes on the base of the carb,if they are not in use,unplug the port and see how it runs.The vacumn tube on the base is normally exitited in between the two primary blades and will act as if you drill the baldes.What you do then is put a small piece...

The normal clearance is .006-.009 with a brass feeler guage,mrmopartech

Send the motor to bobby joseph in dallas georgia and have it done right away,the amount for the shipping would be worth it,to have it back in a few weeks,mrmopartech

Steve,solve all your problems with 1 phone call to Bobby Joseph at 1-770-443-8874,for all the small block needs,call him on monday,mrmopartech

If you can forward the name of the person with the tunnel ram,I would be greatfull,as this is perfect for a street applacation,for my use,mrmopartech

From the great white north,we wish all the members the best holiday season and the best in the new year,from Mr&Mrsmopartech

Maybe you should have your freind post what happened,and the reasons why,and what he did.This way we can get the full story from the horses mouth.It might be the costumers fault,it might be the builder fault,but the true story should be told and we see who(COULD) be at fault,mrmopartech

I worked for Ray barton when he was in montreal,great person,mrmopartech

Depending on the motor and its condition its worth about .03-.05 tenths of a second on the strip.It does work and if you have a well tuned ear,you will hear a difference in the starting and running of the motor,Mrmopartech

Get small valve 318 heads and then have some fun,niece port and match with some good bowl work,happy days are here again,Mrmopartech

Problem solved,make a post to BJR,and ask him to help you,the deal is done,so call bobby at 1-770-443-8874,this is his NEW shop number and will help you to chose the right amount of head work,mrmopartech One question to ask your self,why does a person buy heads from a guy some 2500-3000 miles...

Heres a problem:If a eddy head flows for example 320cfm,thats great.But if you only have a cam that can only use 80% of that,and the rating up to that piont is only a half dozen pionts above the stock heads,and you know you can do bowl work and match and porting to a good degree,whats the piont...

The only way you are going to grain 100% from those heads is if you put a big cam and have alot of rpm,7500+ to make them work.Will their be a increase in power,just by bolting them on,YES,but no where near the power you would think of.One you never mentioned the max rpm you will shift at or...

Kirk,you have not mention at all the motor size or your intend rpm of shifting or use for the car.Both sets of heads can be great if used in the right applacation forum.A 360 street motor will benifit more with the "J"s on it,where as a strickly race motor for the weekend will be great to use a...

Get a 185 degree thermostat and a new rad cap that holds 16-18 lbs PSI.Recheck the timing and make sure the total timing does not exceed 36 degrees.Make sure you have a 50/50% water and anti-freeze mix.Does the tranny cooler lines go into and out of the rad,and to a nother cooler? if so,seperate...

Toby,before buying a cam,tell us the heads you intend to run or intend to buy first,then we can tell you the cam to buy based on driving condition you intend to do and rpm limits you wise to drive under.Is this a highway/street car/cruising car? Some thing to have fun with,not to crazy,but can...

If its a daily driver,get a 600 vacumn secondary carb for it,and jack it up to see what gears are in it.Also go to 15 inch rims and tires in the rear.If you are spinning the boots now,gears are just going to make it worse,taller tires and rims,Mrmopartech

Is the motor a matching numbers motor for the car?If so,a stock rebuild with some minor touches.If you can get a nother 340,then go all out and make it scream,Mrmopartech

If it will land up being a mild street car,a dual plane manifold is needed.The type of driving you itend to do needs to be pionted out and the rpm range you wish to drive in the most needs to be mentioned to chose a cam and the right manifold.Do you know what heads you have,or can get,and what...

What are your cam specs for the cam you are using.What typre of rpm do you intend to run at.What are they asking for a set of eddy small block heads now,mrmoaprtech

Bobby,I think this would be a great idea and would benefit every one at all different levels of knowledge and performance level.I guess my phone bills are going to get allot large this week,Mrmopartech

SO lets do this Mr.moper,I give you BJR number to call him and do your talking to him and he can explain it to you.BJR,1-770-955-0659.If you are a pessemist,then even after a good talk on the phone and facts and figures,you should still not believe any more than you do now,and will not come up...

MR.Moper,what would it take to convience you of head flow numbers,or to stop you from thinking that the numbers are fixed!If it was some one just starting out,I agree with you 100%,but when some one has been doing this for some 20 years and with some big names,you have to sit back and say,I have...

Bobby,this is a great piece of tech info for all of us,you are the man,Mrmopartech

All I grow now is long white hairs and drink canadian beer all day long and build motors for freinds and customers and show them how to run a motor on 9% alcohol beer.When my american freinds come by they tend to be blists after two canuck beers and I am still going after 2-3 cases of that so...

If the average guy does not listen to all sides of story or just goes off in one direction with no real info behind them,disaster will be forth coming.Is a SS/IA car tricker than a street car,for sure,but if a person plays his/her cards right and does not have the rule limitation as a SS/ car...

This one of many times we went south of the boarder and won.This is the 76 SportNationals in Bowling green Kentucky,the best go to these meets and you can say that a small motor can,t perform,if that was the case,the little 4cyl and V6 jap motors would not be running times of 7,8,9 second...