Search results for query: *

  1. D

    Fuel Pump Issue?

    Good Day, I am having a fuel issue and not sure what to check next. After driving about 45-60 mins the car stalls and my filter is dry. I have the 5/16 line from tank to pump then i had 3/8 to the carb. I have switched to 5/16 all the way, replaced the pump, blew air from the tank going forward...
  2. D

    In car gasket replacement

    Is it possible to replace the oil pan gasket only with the engine still in the car on a 67 dart?
  3. D

    Alternator plug ins

    After finishing my HEI conversion I started the alternator upgrade to the 70's type and the electronic voltage regulator. Ive used a factory plug from the regulator to the alt. but I'm unsure where to plug the ends into as the original had only one field spade. I see one is in a ceramic type...
  4. D

    HEI conversion issue

    I did the HEI conversion on my 67 dart. Using a factory electric distributor, installed the magnecore wires, new cap and rotor, new module. The only part not new is the coil I used the one from the doner vehicle. Car will start and idle but when I give a little throttle it runs very rough and...
  5. D

    Carb choice

    I have installed a semi built 64 225 in my 67 dart. Among other things like the radiator drain decided to fall off and about 30 pounds of sludge coming off the original motor in the driveway the carb I have, a carter bbd 2 bbl from a 67 318 has the fuel inlet in a bad spot also the choke linkage...
  6. D

    How to remove dip stick tube

    Is it possible to remove the oil dip stick tube without damaging it?
  7. D

    2 slant questions

    I'm planning a motor swap due to an almost seized bearing, the new motor is a 64 going into a 67 dart- Any problems between these two years. All ive seen so far are a couple extra water holes that need plugs. Second is there a special tool or a trick to removing the TC bolts. Not much room on...
  8. D

    rbo EFI slant in Seattle

    Not mine-just in case someones looking to go this route. post id: 5469476285. If it doesn't come up correctly it in seattle craigslist under slant 6. Its a turbo efi,title missed a couple letters.
  9. D

    Gasket replacement

    I'm replacing gaskets on a 65 slant and noticed the tabs at the rear seal/oil pan are missing. Are these a necessary item. I didn't see any oil around the block just on the pan in a couple spots.
  10. D

    Timing Covers

    I was wondering if different years of slants have timing tabs in various spots on the timing cover or possibly none at all. I pulled the cover off one and theres no timing tab on it. If I read the block correctly its a 65
  11. D

    Idle Issue

    Good Day, I have a 67 with the holley 1bbl that was sitting for about 20 or so tears. The person i bought it from took out the tank and ran a chain inside to break up varnish then steamed it. It runs ok with the choke but after it warms up it will only run with slight pressure on the throttle...
  12. D

    Need help/advice

    Anybody in the tri citys area that might be able to help or give me a direction to go. I have a /6 that will run with the choke on but once it kicks off it doesnt want to idle. I have replaced the items in the kit and its helped a little but still idles very rough. Car has been sitting a while...
  13. D

    Alt. Replacement

    I was reading some of the threads on the guys replacing their alts with the bigger 90/120 units and saw all the extra upgrades with wiring that had to be done. So if going from the small 37 (50) to the 60 is the same amount of work required or would the be a direct bolt on. I would like to just...
  14. D

    Old vs New

    More shots as progress happens. Always something rebuilt the trans and didn't realizt there is a difference in the tails between a colum and floor shifter. 1st off to the carwash for a good cleaning. Plus a bonus from our last car show,for more see under cascade- cool desert nights :happy2:
  15. D

    Here we go

    Well seeing how everyone is out of stock on the head studs were putting it together with the bolts. More as we get it assembled. Oops sorry about the girlfriend shot :cheers:
  16. D

    Engine Mock-up

    Thought I'd give a few shots of the uncompleted tower. Enjoy
  17. D

    Oli Slinger Woes

    Ok so I put the slinger on in front of the crank gear like the book shows both ways and it is getting chewed up by th cover or the gear. Does this need to be in? Is it compatable with the double tooth gear? Lastly does it go between the block and gear instead? Woe is me ....
  18. D

    Oil Slinger

    Any leads on where to get the oil slinger for the crank? Somehow, somewhere it got lost.
  19. D

    Strombergs or Holley 94

    I tried doing the search and found nothing just curious if anyone has tried or heard of someone using a set of the stromberg 97's or the holley 94's instead of the single four.
  20. D

    Crank Bolt Size

    Thanks to everyone here I have gotten the old 67 roadworthy again minus the steering box,but thats another day. I started on the new motor and can't find the crank bolt. Any idea what the size of it is. Need it to turn the crank while torquing the rods plus its a good piece to have around for...
  21. D

    Cam Choice??

    Good Day. Its cam choice and I am totally clueless at it. Heres the specs:Block is 030,oil passage mod,decked 080,Head shaved 080,ported to the Aussie gasket,polished,large valves,stiff springs,dual shortie headers,hurricane intake ported to gasket,8 3/4 rear gears ??,auto trans. Thats all I can...
  22. D

    Intake/Exhaust removal

    Okay I need a little assistance here. I have all the bolts off except the main PITA under the exhaust. I am trying to get two apart seperate. Is this possible or do I need the one remaining off. Im thinking its holding everything on but....Appreciate any help with this.:read2:
  23. D

    Assembly lube

    Hey Guys I'm finally starting my engine assembly and need opinions on the lube to use for the bearings. Do I need to oil the cylinder walls before sliding pistions in? Any other tips are Greatly appreciated. Thanks.
  24. D

    Engine weight

    What is the weight of a 70-71 or so slant complete less trans. Thanks.
  25. D

    Carb Question

    Well I was going to post this on the /6 forum but forgot my info so heres the ?? Which will work better for the 4bbl intake..the holley 390 or the predator 6000 which is also a 390. Thanks for the input.
  26. D

    Slant Scoops

    So how 'bout some pics of slant hood scoops
  27. D

    Radiator 4 a slant

    OK so Im having a problem with the cooling on the dart. I replaced the therm and found the old 1 backward. I put the new 1 in correctly and it heats up even quicker.Coolant has been flushed and looks good. I dont want a heating issue wiht the new motor so what other options are there for another...
  28. D

    Carb Question

    Good Day,Has anyone tried running 2 2bbls on the dual 1 intake? How 'bout something else? I did some questioning and so far a shop wants to put 2 350's on it. I thought it was a bit excisive for a mildly built 6er. Any suggestions,ideas,hints or references are greatly appreciated. Thanks. Dean
  29. D

    Porting Help

    Hey All; I was wondering if anyone has a spare intake gasket I could use as a porting template. I dont want to buy the whole set since I just need the steel gasket or if there is a porting template going around?? Thanks for any help. Dean
  30. D

    Now What??

    After removing all the paint & 12 lbs of bondo's on the 67 gt's passenger fender I find it's not the original and all the holes for the GT trim are homemade. Everythings off by 1/4 to 3/4", no hole for the fender turn signal. Here I thought I had an all original 67 /6 gt. :sad8: Anyone have a...
Back
Top