Search results for query: *

Hey FABO, I need input from the body and paint guys. I have my current build assembled, gapped and panel matched for final priming and blocking. I spent over 50 hours installing and adjusting everything to get it close enough. I will be shooting color in a couple weeks then be ready to assemble...

Question for you body and paint guys, how many quarts of sprayable single stage color do you mix for the body and required jamming of a mopar A-body car. Assume good coverage in 3/4 coats on the exterior. Interior not included here, it is a different color.

Can someone post photos of how the cowl-radiator to hood gaskets install on a 67 Barracuda? I have two gaskets left, a long one and a short one and I have no idea how they install. Any advice much appreciated! DR-----------:-)

These items came out from the front end fenders or suspension and I am at the stage where I need to install them but cannot remember or find documentation where they go on a 67 Barracuda. I would appreciate some guidance------------------DR-------------:-)

I am to the point of installing the front fenders and grille. I have the hood installed and gapped at the cowl and am ready to assemble the rest. I have the seam sealer for the fenders and most of all the new rubber and fasteners. Anyone suggest a sequence to follow from here? Any advice...

All: I am at the stage that it is time to refurbish my 1967 Barracuda grille. To that end, I need new turn signal lenses and gaskets. Also, the orange bulbs that go in them. Or do they make an orange lens that fits the housing? Can anyone tell me where to buy these? My search did not turn up...

Can someone please post a photo of the factory horn location on a 1967 Barracuda. I am trying to finalize the engine bay wiring and installed a radiator overflow tank next to the radiator. I think I need to relocate the horn mounting. Thanks for the help...

Can someone post up a photo of the location of the dart-charger badging that says "273 four barrel"? I need to know the location of said badging on the original cars. TIA------------DR------------:coffee2:

I got my 67 notch doors close on adjustment (not finalized) and my door glass installed and quarter glass working with new front seals. I installed the roof rail fittings and rubber gasket, my question is should the glass roll up into the slot in the roof gasket for lay to the outside of it. I...

Installing all the hardware in the doors on my 67 Notch. I thought I had bought everything I needed but the door glass front edge has a seal that clips into two holes in the glass. I have searched and googled and am coming up dry. Any advice will be much appreciated. Cheers-DR:coffee2:

Got my new 68 F & R glass gaskets and clips today. I have the diagrams of where they go from searching the forum. Can anyone post a photo of the correct orientation of the installation of the clips? If I get them installed the glass shop I do business will come to the shop and install my F & R...

All: I ahve searched the forum for a couple days and have come close but have a question. I am installing my deck lid hinges and torsion rods and cant remember the assembly sequence. I have all the original complete parts and photos but I am having trouble with the assembly sequence. Any help...

OK, I searched but did not get an answer. I am trying to buy a California Car Cover for my 67 Notch and they only have them for the 67 fastback. CCC says their cover will work on my coupe body but I am skeptical. Any firsthand experience out there? TIA-Rat:coffee2:

Checking interest: I am reconditioning the taillights for my notch and it looks like I will have two complete driver quality units left when I am done. One for each side. I will post photos in the for sale part of the forum tomorrow but I know they are hard to find and I bought a couple sets but...

I know this has been discussed but I am out of the loop. Does anyone repop the drip rail bright trim for a 67 BC notch? I have a vinyl top and have to have it and I damaged mine taking it off. Also I would like to buy 68 Notch front & rear windshield bright trim, new used or repop. I know they...

My companys' shop will be vacant from about 2:00 PM today until 7:30 AM Monday morning. I am moving all my painting supplies and parts into the shop this afternoon and working on my car straight through the weekend. Hope to have the hood, trunk, front fascia and both front fenders in full color...

Getting ready to prime & block the BC. Have any of you ever used the Abranet product? I think that is the way I am going to go. Should be a lot faster if I can find the blocks I need. DR

While beadblasting my upper & lower door hinges for rebuild kits, I noticed that the uppers had bronze bushings in the upper & lower pin lands. Did Ma Mopar ever build them new that way. I dont believe these were ever off the car or rebuilt. Just curious, thanks. DR

I have spent the last 5 days bead blasting all the parts from my car that will fit into our large cabinet including the nuts & bolts. Can anyone suggest a way to finish them to a satin black that won't chip away the first time I put a wrench on them. I have to do something but I have had no...

It looks like I can get my original bumpers rechromed for about $325 Ea. by the people who did my last car. The quality on the last set was superb driver quality. I can buy repop bumpers for about $290 Ea. I am afraid of them as they could be import and low quality. Have any of you had...

I need advice on where the best place to buy weatherstrip for my 67 notch? I want to replace everything but can't seem to find anyone who sells a complete Kit. Any advice appreciated!!!! DR:read2:

Can anyone tell me with difinitive authority what flat hood will interchange with the bumped hood on the 67 barracuda's? I don't want to reinstall my stock hood and I am looking for alternatives, close guesses won't do as cash will be changing hands and well------------------you know------------...

Thinking about my hood and not being particualrly fond of the hood inserts--- Wondering if anyone here has taken them out and modified the hood. Also, I like the idea of hood louvers had anyone here done that? TIAn Rat

I am ready to replace the windshield and rear glass gaskets on my 67 Barracuda notchback. If I re-use the existing gaskets is the original-type lock strip available? If I go with the 68 gaskets is the 68 trim available either used or aftermarket? I need to replace the headliner and vinyl top so...

Where can I get the special driver for the fuel filler door screws. When I did the tank, I put phillips screws in it but I know it will get taken unless it has the fiddle-free fasteners. TIA-Rat