Sorry meant super stock
Accel 8140: Super Stock Points Ignition Coil 12-Volt | JEGS
Accel 8140: Super Stock Points Ignition Coil 12-Volt | JEGS
Stop in for a cup of coffee
- Thread starter toolmanmike
- Start date
-
Bill I probably scrap the one you need. Remember out of ten cores four are junk. Strip them for parts. So the cost is...…………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………………..………………………………………………………………………………………………………………………………………………………………………..nothing but the ride
So, no resistor ?` And it works with the points too ?
That's a stock replacement so you want the ballast.
Just picked up a couple a/c idle solenoids. Score!
GM (DR) stamped by chance?
Big $$$ ones
Stamping# DR1114421
Part# 3514520 Early (Carter AVS)
Part# 3549318 Late (Carter AVS)
1970 440
Carburetor: 4737S, 4739S, 4741S, 4740S
Hex head with cap, no integral bracket
Stamping# DR1114442
Part# 3514892 (Carter AVS)
1970 340
Carburetor: 4936S, 4937S
Round head, no integral bracket
Stamping# DR1114442 or DR1114447 (Evidence of either number being factory original)
Part# 3438303 (Carter AVS)
1970 440 4738S
1971 440 4968S
Hex head with cap, no integral bracket
Stamping# DR1114441
Part# 3438777 (Holley)
1971 383 4667A, 4734A, 4668A, 4735A, 6191A, 6193A
Hex head with cap, no integral bracket, but includes wiring harness
Stamping# DR1114429
Part# 2875975 (and Part# 3438333) (Holley, Carter AFB, Carter Thermoquad)
1970 440+6 4375A, 4734A, 4376A, 4144A
1970 340+6 4791A, 4792A
1970 426 4745S, 4746S
1971 426 4969S, 4970S
1971 340 4972S, 4973S
Round head with integral bracket
Stamping# DR1114443
Part# 3438338 (Holley)
1971 440+6 4669A, 4670A
Hex head with cap
Stamping# DR1114420
Part# 3412059 (Holley)
19691/2 440+6
Hex head with cap
Stamping# DR1114421
Part# 3514520 Early (Carter AVS)
Part# 3549318 Late (Carter AVS)
1970 440
Carburetor: 4737S, 4739S, 4741S, 4740S
Hex head with cap, no integral bracket
Stamping# DR1114442
Part# 3514892 (Carter AVS)
1970 340
Carburetor: 4936S, 4937S
Round head, no integral bracket
Stamping# DR1114442 or DR1114447 (Evidence of either number being factory original)
Part# 3438303 (Carter AVS)
1970 440 4738S
1971 440 4968S
Hex head with cap, no integral bracket
Stamping# DR1114441
Part# 3438777 (Holley)
1971 383 4667A, 4734A, 4668A, 4735A, 6191A, 6193A
Hex head with cap, no integral bracket, but includes wiring harness
Stamping# DR1114429
Part# 2875975 (and Part# 3438333) (Holley, Carter AFB, Carter Thermoquad)
1970 440+6 4375A, 4734A, 4376A, 4144A
1970 340+6 4791A, 4792A
1970 426 4745S, 4746S
1971 426 4969S, 4970S
1971 340 4972S, 4973S
Round head with integral bracket
Stamping# DR1114443
Part# 3438338 (Holley)
1971 440+6 4669A, 4670A
Hex head with cap
Stamping# DR1114420
Part# 3412059 (Holley)
19691/2 440+6
Hex head with cap
They came off thermoquads. I really need one for my Swinger. Dealer installed air didn't come with one.
Some of the ones listed also were used with the E vac advance. I would think the AC cars needed a bump also.
Will that work on all 12V points systems?
I'll have to look when I get them.
Sitting at airport waiting for son. Little airport outside of the city.
Today’s recap, cleaned up shop some, pulled remains of seat from Fargo. There was a sheet metal pedestal spot welded to floor. A few quick cuts and a couple back and forth bends. out it came. Pretty much a clean slate. Stuck a pt cruiser seat in the drivers side,happy with the proportions.
Did some shopping,found a led bulb to replace the halogen tube in my worklight. Should be nice!
so now a 45 or so minute wait.
Today’s recap, cleaned up shop some, pulled remains of seat from Fargo. There was a sheet metal pedestal spot welded to floor. A few quick cuts and a couple back and forth bends. out it came. Pretty much a clean slate. Stuck a pt cruiser seat in the drivers side,happy with the proportions.
Did some shopping,found a led bulb to replace the halogen tube in my worklight. Should be nice!
so now a 45 or so minute wait.
R4Sedan
Larry
Cool those are hard to find.
A brand new 1965 Dodge station wagon brochure arrived in the mail today.
Bill
Bill
This one took me years, about 4, to track down. Cost me a bit more than I’d like to admit but worth it
Unconventional
Well-Known Member
I think that's the same Accel we used on the all powerful 40 horse VW in the race buggy. About the only parts of the motor that didn't have to say VW on them. We could run headers too, those stock VW exhausts were not known for their good ground clearance
It says in the brochure I got that the 1965 Dodge Dart 170 station wagon did not come with a carpet. Now I got very curious. What did it come with ?
Bill
Bill
Rubber/Vinyl floor mats and rear mat.....
Ddaddy
Just doing what I do
Rubber floor mats.
Ddaddy
Just doing what I do
Instant mind meld!
I was running a pertronix ignitor 2 in my truck and carried points condensor and coil in the truck. The modual burned up and it now has the points again. I still made it home.
Pretty sure its a blend..I doubt that they were 100pct rubber....
-
Similar threads
