Search results for query: *

  1. howiedodat

    1968 Plymouth Satellite

    It has been sold. I was trying not to bump it up and didnt know how to mark it sold. Thanks for the kind words!!
  2. howiedodat

    1968 Plymouth Satellite

    Its decals that I had made up. Thanks !!
  3. howiedodat

    1968 Plymouth Satellite

    Here is my 1968 Plymouth Satellite. The information on the car is listed below. Everything below I have done to the car in the past 5 years I have owned it. The body and paint are an older spray. Looks very good but it is a driver with a few chips and scratches. The lower quarters were nicely...
  4. howiedodat

    Clutch vs. Electric Fan

    For my .02, I was running a clutch fan on a new Moroso water pump. My new pump's bearing pushed out at 5000 rpm's. Destroyed my very new rad and fan. Needless to say I went back to electric with my new rad.
  5. howiedodat

    Need a tow?

    It'll buff out............
  6. howiedodat

    Mighty Demon 750 VS dual feed

    Here is a Barry Grant Mighty Demon 750 vacuum secondary annular discharge carb. Just off of my 1968 Satellite. The carb is about a year old and just off my car. I have included a photo of it on the motor. I bought it new. Included is the dual feed line, the manual and a Russel fuel pressure...
  7. howiedodat

    fabricated valve covers

    Hello gents. I have a set of the tall aluminum valve covers like you see on ebay. Mine are Procomp (SBM) and cleared my Mopar Performance hold downs. I switched to the elite tall myself. They sealed well. Its a ***** getting the long bolts to start. Mine are the satin finish. No dents with both...
  8. howiedodat

    can't get idle lower than 1000

    Sounds like the primary throttle plates are not set correctly. Take the carb off and set visually. I think thats what POS Dakota refers to in his post.
  9. howiedodat

    Edelbrock D64 Dual 4BBL for a 273

    Hello, Will this accept square flange carbs ?
  10. howiedodat

    Alignment tweaks to improve tracking?

    Autoxcuda, will those numbers work well on a 68 B body ? Thanks
  11. howiedodat

    Rear Shock Lower Mounting Studs

    Thanks for the thoughts !! If anyone is interested, the studs are welded at the face side of the shock. I cut the stud close to the plate on the shock side then ground down the face till flat. Then I drilled the locating pin out to the proper size and mounted the new stud. The studs were from...
  12. howiedodat

    Rear Shock Lower Mounting Studs

    Hello from a B Body member !! I am about to replace my rear spring bushings and install new KYB shocks. When I purchaced the car I put a "inexpensive" rear shock on the car. I managed to break the threaded portion of the stud off the mounting stud. I welded a new threaded portion on the stud...
  13. howiedodat

    727 throttle pressure adjustment

    Whats happening is the lever, when disconnected from the cable, that is adjusted to WOT, will continue approx. 1/4 inch to the idle position. I did put a spring to be sure the lever returned to its furthest travel to idle. I belive I will try the adjusment as to shift speed. It seems to hold...
  14. howiedodat

    Anyone using Lokar kickdown cable?

    Hello All !! Sorry, I don't have any help, but I also am in need of some thoughts on the kickdown adjustment. My question is, What is the proper adjustment of the thottle lever throw with the Lokar cable ? I have searched the forums and haven't seen this particular issue discussed. My throttle...
  15. howiedodat

    727 throttle pressure adjustment

    I have the same or similar book on my '68. I read it to be the factory says to adjust the travel so the lever is at the idle position then adjust the linkage for the proper shift points. However, the Lokar cable instructions (and many others in the forums) state the lever should be at full rear...
  16. howiedodat

    727 throttle pressure adjustment

    Hello All !! Sorry, I don't have any help, but I also am in need of some thoughts on the kickdown adjustment. No offence and no intention of hijacking the thread, I just don't think a new thread is needed. My question is, What is the proper adjustment of the thottle lever throw with the Lokar...
  17. howiedodat

    727 throttle lever, kickdown lever

    Another A Body member comes through in the clutch !!, so to speak. I can't say enough good things about the help and information I have received from the site and its memebers. This is, by far, the best site for information on Mopars I have used. Raisin Pie for Dusterdood. Thanks for the help...
  18. howiedodat

    727 throttle lever, kickdown lever

    I am in need of a kickdown / throttle lever for my 727. Mine has come up missing after the tranny swap. This is the arm that mounts over the shifter arm on the drivers side of the tranny, for those of you that know this part by another name. Thanks.
  19. howiedodat

    360 small block info

    Thanks Folks !! MY general concern is that I know I have a neutral convertor and the B&M flex plate for externally balanced 360 so goes the motor, I should be good. Thanks again !!
  20. howiedodat

    360 small block info

    Hello All !! My 360 is, I believe, a 1970 model. When I removed the heads j code and ran the numbers, they came back as a 1970. My dilema is all the sites I have searched dont list a 360 in passenger cars till 1971. I assume that means my motor is a truck motor. No problem, but I am hoping...
  21. howiedodat

    regulator question

    HHHHMMMMMMMMMM It seems that it is a no.
  22. howiedodat

    regulator question

    ...from one of these 100 amp pieces. Thanks to all !!! Here is the part I am refering to, its listed for a 1975 Roadrunner Part No. VR125 Standard Motor Products Voltage Regulator Voltage Regulator: Rwd, Except 86, 100 Amp, Except Leece Neville Equipped Warranty: Limited 1 Year*
  23. howiedodat

    Mopar Jacket

    :love7::clock:
  24. howiedodat

    Mopar Jacket

    I have the following jacket on ebay. Nice and new just too small. 8) http://cgi.ebay.com/ebaymotors/MOPAR-DODGE-PLYMOUTH-RACING-RAM-JACKET-HEMI-XXL-BLACK_W0QQitemZ110230465018QQcmdZViewItem?hash=item110230465018
  25. howiedodat

    magnum intake waterneck

    I just put an M1 on my 360. It used the late model housing and is does use a diff thermostat from the LA housing. Bought the intake from Summit and they didnt tell of the difference until after I called them as to why the LA housing didnt fit.
  26. howiedodat

    carlisle 2008 roll call......

    Thanks for the link. I wonder if some of you folks that have been to this event could share how it works ? I would be driving the car I would be "showing" so I would need to be able to take the car back and forth from the hotel and such. Is this a problem or does the car have to stay on the...
  27. howiedodat

    decal on quaterpanel ideas

    I favor the "Plymouth" Superbird style decal. Cant imagine why.
  28. howiedodat

    carlisle 2008 roll call......

    Would someone post the link for sign up for this event ? Thanks :-D
Back
Top