Search results for query: *

I spent some time looking for options on a 28x12 and ended up going with a Nitto 555R since they were about $75 less than the Mickey ET Streets in the same size. I was hoping to go more of a street tire, but I'm limited by the size of the wheel (17x11), but the Nittos appear less aggressive...

I'm trying to get into the 2025 Auto Value parts store calendar. The voting runs from Aug 1 - Aug 14 and you can vote every 24 hours. Would any of you be willing to vote for my Duster? It's super quick and would be appreciated!! Just click the link and vote daily if you could! The...

72 Duster 440, 4 Speed 215s up front and 315s put back. For front brakes I am running the SSBC 11" 4 piston disc conversion, which I think just use KH calipers, with their upgraded pads, it have a set of Power Stop pads ready to install. A153 Front Disc Brake Conversion Kit, Mopar Non Power...

I picked up a new Performer RPM intake and when I tried to install it, the bolts holes were all off 1/2 a hole in height. The M1 that came with the engine ended up going back on, which was also a challenge to get the bolts started, but eventually they all fit. I am assuming since the new...

Does anyone happen to have a 73+ centerlink laying around that could snag a few measurments for me? I bought one and the guy says it's from a 1973, but when I went to install it, it's about 2" longer than my old one. The outer tie rod holes are 24.5" apart, whereas my1972 one is 22 about an...

I finally pulled my cam out to see what it is, it's an old Crane CCH-312-2-NC. It's a single bolt cam that I can't find any specs on it, but I have found the specs for the 3 bolt version, which I will guess are the same, since I measure the duration and lift and it matched. My question is...

I'm looking to convert my steering to the later style for some additional clearance and am looking for a 73 and newer centerlink for my Duster. Let me know what's out there

Like it says, I'm looking to swap out pans to gain a little more ground clearance. I currently have a Milodon 7 qt but it's sits right around 3" off the ground. I came across this one from 440 source, it would gain me an extra 1.25" of ground clearance, but I'm curious if anyone has tried...

Which mark do I use? I've had this motor together forever, switched over to EFI about 8 years ago and can't remember which mark I used to time it. They are about 7 or 8 degrees apart.

I pulled my rear suspension out yesterday to replace the leaf spring bushings. The front bushing is 1.5" and the rear is 1". I was wondering if someone could help ID what they are out of. They came in my Duster, I was told they are 65 B Body SS springs, but I can't find anything related to...

Trying to use the rest of this nice weather we are having as best as I can. I put some miles on today cruising around to the local picture locations. Some of these I collected earlier in the summer. Just thought I'd share.

Does anybody have a set of 305 tires on an 11" wide rim, preferably a 17" diameter? I have 315's on them now, but looking to go taller, and it appears I have to go to a 305/45r17 to gain a little height. Just wondering how it'll look, the 315's almost look too narrow, nervous a 305 with be...

72 Duster, steel headed 440, PST 1.03 bars, QA1 uppers, lowers and strut rods, Hellwig sway bar, B Body SS springs and mini tubbed. I currently have RCD Bilsteins front and rear, but they seem pretty stiff. Even when I sit on the front of the car, it barely moves. Car sits pretty low, so I...

Just a quick question. My buddy lost second gear in his trans so I am letting him borrow my 727 that was laying around. His was a manual valve body, mine is not. He doesn't have the linkage for the kickdown installed, since it wasn't needed on his trans. Can he just wire the kickdown...

I forgot someone filmed my car idling a while back, so I figured I'd share in case anybody wondered what Dynomax Ultraflows sound like. In the video it has Pro Parts headers, reduced down to 3" with a H pipe, Dynomax Ultraflows with 3" tail pipes and turn downs at the bumper. I currently...

B&M Quicksilver Shifter in black chrome. Bought it last year and used it for the season, no longer needed. The only part that I used was the shifter itself and the cable. Everything else is brand new, however, the plastic housing does have a couple scuffs from storage which the pics show...

I'm looking for a spare set of tail lights for my 72 Duster. Looking for a set with clean lenses to use on a driver quality car. Thanks

I'll start by saying everything in the brakes is less than 2 years old. I just swapped to a manual trans, and now that everything is back together I notice my brakes are dragging to the point where it's very hard to push the car on flat surface. If I lift up the brake pedal just a bit...

I just came across this from Holley and it seems like a good option for finally having an accurate fuel Guage. https://www.holley.com/products/fuel_systems/fuel_tanks/fuel_tank_accessories/parts/19-250/?

Does anybody run a 17" wheel up front and a matching 15" wheel out back? I currently have 17" Torq Thrusts and will need new tires soon. I'd like to go bigger out back, but there are no offerings for a 17" wheel that aren't a bias ply slick so I was thinking of swapping a set of 15's on...

I am in the process of swapping my auto for a 4 speed. The engine is a 1970 440 with a forged crank. The crank had a bushing in it already and the trans bolted right up. I went to replace the bushing with a new one, but the new one doesn't fit. The new bushing is correct at a 0.940...

I'm looking for the nuts needed to secure the console top plate to the console base. I tried some random small hardware I had on hand and nothing fit. Are these something I can get at a hardware store, or am I out of luck? I don't need factory original ones, just something that works.

I see most if not all people mount their hydraulic clutch master cylinders at an angle where the factory push rod goes through the firewall. I am assuming this is for the correct pedal ratio, and the fact that there are mounting brackets readily available. My issue is my headers, I am running...

I currently have a 440 in a 72 Duster that is running a 727. I'm about to swap to a 4 speed (833) and wondering if anyone has experince with Pro Parts headers. They are currently on the car, and it sure doesn't look like a Z bar will fit in there. I have bought the hydraulic throwout...

Looking for a 4 speed handle for a bucket seat console car. Bayonet or bolt on style will work, (prefer bolt on) I have a rebuild kit for the shifter that has both style stick bottom assemblies so I can use either one when I rebuild it.. Let me know what you have!

I'm starting to collect parts for my 4 speed swap and have found a trans and pedals locally but it doesn't have the shifter with it. Looking for a good condition usable Hurst shifter and the shift rods for an A body 833. Let me know what's out there. Edit: Found a shifter, still need the...

I'm trying to determine which K member is in my car. I've spent all morning looking at various pictures and am still confused. I'm looking to possibly install the QA1 K member and am trying to identify what motor mounts I would need. It's in a 72 Duster that was originally a 318, but it...

Does anybody here run these springs on a Duster? I am looking at replacing all of my spring bushings over the winter and debating on just getting new springs. Mine are currently a hodge podge of B body SS springs with some leafs removed, so I do not know how the ride height would compare...

I couldn't really find anything that specifically said it could, but I am looking for a replacement headlight switch that is also able to dim aftermarket guages with LED lights in them. The factory switch obviously doesn't have that low of resolution and it's either on or off, but getting them...

I'm looking for the parking brake handle/lever that mounts under the dash. It'll be going in my 72, so I think there's a large range of years that'll work. Thanks