Search results for query: *

  1. 69MOPE

    Add your abody driveshaft length for quick reference

    ALL lengths must be measurements from the center of the front u-joint cap to the center of the rear u-joint cap.
  2. 69MOPE

    Add your abody driveshaft length for quick reference

    111.0" -- 1967-'76 Dodge Dart, Plymouth Scamp 108.0" -- 1970-'76 Dodge Demon/Dart Sport, Plymouth Duster 108.0 -- Plymouth Cuda 67 68 69 108.0" -- Plymouth Valiant
  3. 69MOPE

    Add your abody driveshaft length for quick reference

    1) Car model/year wheelbase (see list below)(108" or 111") 2) Engine (small block/big block) 3) Trans (904/3 speed OR 727/4 speed) 4) Rear (7 1/4, 8 1/4, 8 3/4, 9 1/4 or Dana 60) 5) Your FACTORY driveshaft length
  4. 69MOPE

    Add your abody driveshaft length for quick reference

    So far (not including pre-67) 111" wb w/ 904/8 3/4=51.99 My 67 valiant has a 904 & 7 1/4 & c-c of joint is 51 1/4 & I'm swapping in an 8 1/4. '67 Formula S, 383/727/8.75 45" 68 Barracuda with a 727 trans. and 8-3/4 rear, everything in stock location took a 44.5" shaft. 1975 Dart...
  5. 69MOPE

    Add your abody driveshaft length for quick reference

    I started this thread as a reference accumulator. I was looking for people to list ONLY their factory stock driveshaft lengths so other people could (using the actual measurements ) figure out what length they need when doing a swap. Most of the driveshaft charts out there are incorrect, this is...
  6. 69MOPE

    [FOR SALE] 413 426 Max Wedge pistons

    1963-64 413 426 Max Wedge pistons, New Old Stock. TRW L2185 standard. These are the pistons needed when boring a 413 out to 426. $800 or best offer. Located 19023
  7. 69MOPE

    I need help! 383 with A/C idler adapter measurements. 69-70-71

    I need the dimension measurements. The height of the short side, the height of the tall side and the distance of the bolt hole centerlines. I hope someone has one lying around and can help with the specs so I can fabricate a steel one. I would buy one but the cast part is crap.
  8. 69MOPE

    A-body Dana 60 5.13 spool in Lafayette Minnesota $400

    Saw this on face book. MUST BE PICKED UP . Lafayette Minnesota. $400 Chad Hoffmann dana 60 FREE Lafayette, MN Narrowed Dana 60, 35 spline strange axles, strange spool, drum brakes, half inch studs, axles have 4.5 inch bolt pattern and 4.75 inch bolt pattern drilled and tapped, has chassis...
  9. 69MOPE

    [SOLD] A-body 3.55 sure-grip rear EBAY/ Mine

    The four I have are pending sale. I will get back to you later in the week if I have any left.
  10. 69MOPE

    [SOLD] A-body 3.55 sure-grip rear EBAY/ Mine

    No the axles are 5 X 4" factory small bolt pattern. It looks like it's going to sell but I do have a few a-body bare housings for sale. And Dr. Diff sells large BP axles for $300.
  11. 69MOPE

    A-body radiator shown in magazine

    http://www.summitracing.com/parts/bci-62175/overview/year/1970/make/dodge/model/dart
  12. 69MOPE

    Dana 60 rebuild

    I have a 3.73 gearset, new 30 spline trac lock and a bearing kit that I bought a while back and I am not going to use it. Give me a few days to dig it out of the garage, take pictures and put a price together.
  13. 69MOPE

    [SOLD] 8 3/4 yoke, coarse spline, large joint (7290) EBAY/ Mine

    http://www.ebay.com/itm/291716189225?ssPageName=STRK:MESELX:IT&_trksid=p3984.m1555.l2649
  14. 69MOPE

    [SOLD] A-body 3.55 sure-grip rear EBAY/ Mine

    http://www.ebay.com/itm/291720483704?ssPageName=STRK:MESELX:IT&_trksid=p3984.m1555.l2649
  15. 69MOPE

    Kermit the frog pic.

    Share it!
  16. 69MOPE

    Cowtown New Jersey swap meet this Sunday!

    I go every year. Very little Mopar but sometimes I get lucky.
  17. 69MOPE

    [SOLD] B body Dana 60 ebay/mine

    http://www.ebay.com/itm/291707240999?ssPageName=STRK:MESELX:IT&_trksid=p3984.m1555.l2649
  18. 69MOPE

    I need a time delay relay.

    I have a 12 volt fan cooling an air compressor in my van that is powered when the compressor is on. I need a timer/relay that allows the fan to keep running for 3 or 4 minutes after the compressor shuts off. Anyone know what I can use?
  19. 69MOPE

    [WANTED] Steel Wheels BBP

    pictures Backspacing is 4 1/2"
  20. 69MOPE

    Is there a doctor in the house?

    Your watch is to tight!
  21. 69MOPE

    [WANTED] Steel Wheels BBP

    I live close to both N.J. bridges at Walt WHitman and Com Barry
  22. 69MOPE

    [WANTED] Steel Wheels BBP

    I have 2 - NEW 15" x 8" and 2 - almost perfect 15" x 6 1/2" for sale. I need to get $225 for the set of 4.
  23. 69MOPE

    Powerball lottery

    If the odds of winning are 1 in 292 million (the exact odds are 1 in 292,201,338, according to Powerball.com). then that means there is only 292,201,338 variations of numbers. So, if you spend $292,201,338.00 and buy every possible number, you are guarantied to win. If the jackpot is $1.5...
  24. 69MOPE

    [WANTED] 2 Wilwood calipers 120-5289

    Anyone deal in Wilwood caliper's or know of any closeout sales?
  25. 69MOPE

    [WANTED] Weld Rodlite wheels 15 x 10

    I need a pair of good used 15 X 10 with 3 1/2" backspace. Must be Weld Rodlite's
  26. 69MOPE

    '89 roller-cam LA 360 w/Magnum heads - new roller lifters not pumping up

    I say, put 16 dribblers in it and try it. Get the high flow squirter's out of there. If they flow that much oil, the lifters will never pump up.
  27. 69MOPE

    WTH is that?

    For $3500, it better have $3450 in cash in the glove box!
  28. 69MOPE

    alternator pully swap

    A larger diameter pulley slows down the alternator RPM's. Good for racing, but bad for idle charging.
  29. 69MOPE

    Check out this landing

    I fell out of my chair.
Back
Top