Search results for query: *

I picked up a "Modified" 225, it came with a Clifford 4bbl. intake, a pair of headers (2 3 port) mated to an 833 4 spd. I was told the head was shaved and it has larger valves and had a 650 Holley when it was installed in a 68 Dodge short wheelbase van. Supposedly gave Camaros and Mustangs a...

Thought I was done parts shopping, but with 5 cars to put together, something always comes up. I was installing trim on my black 66 Barracuda when the very front clip on the passenger side quarter spear broke. I gently worked my way rearward removing it to try to find a replacement clip...

I had the good fortune to score a complete 1966 Mopar parts book, we'll, almost complete. I am ready to start installing the interior which is in several boxes. When I went to my trusty right hand parts manual, the only illustrations left in the interior parts section are for the Imperial...

After 2 years, finally got the 318 fired in my black 66 Barracuda. When the block was worked over at the machine shop, they removed the oil filter stem and plate. We have tried 2 different plates and 2 new oil filters and still have a significant leak. Any suggestions? This project has long...

Anyone know where I can get a filter for the in tank sending unit for my 66 Barracuda? I ran these part #s on line and came up empty. 14-86-85 and 1670-694

Not Mopars! Anybody out there know where there are any mid 50s ford trucks? I would like to find an original set of stainless dog dish caps with the ford lettering on them in red. Paint can be faded. The repops are only available in blue for 3/4 ton or no paint. I acquired a 56 F-100 that a...

The 904 in my black 66 came out of a 75 Valiant, it has a 3 prong switch. I need a single prong.

As per any header installation, these are not plug and play. Had to remove steering column, replace OE coupling with a round universal, shimmed driver side mount 1/4" and place strategic dimples in the tubes.

1992 Dodge Dakota Magnum exhaust manifolds. 2-1/8" outlet, wire brushed and heat painted. $175.00 plus the ride. Includes new mounting bolts, washers and lock washers. Located 25 mile SE of Pittsburgh, PA. PM an E-mail for photos showing casting numbers.

1968 long tail shaft 833 complete with levers, rods and shifter box. $700.00 obo. Located 25 miles SE of Pittsburgh, PA PM an E-mail for photos showing casting numbers.

Why did I have to fall in love with an Early A? Did not want to hack up a rotisorie restored car to install fenderwell headers, so I talked to the good people at Sanderson who said some had made DD7 blockhuggers work. Bought a set - wont clear steering shaft. Following other comments on this...

Finally scored a set of 92 Dakota exhaust manifolds for the 318/360 head engine in my black Cuda. I need mounting bolts and head pipe flanges and bolts. Any recommendations for a source?

Not mine! Listed on Pittsburgh CL. 1965 Barracuda A833. I went and took a look at it, in excellent shape. Owner asking $700. Located in Charleroi. Pa I have a contact phone #.

Went to the Saturday night cruise at Norwin Hills near Irwin, PA last night. Usually aren't many Mopars let alone A's.I walked up to a Duster from behind, looked like a slant or 318 car - plain Jane, column automatic and bench seat, stock wheels and caps, skinny tires. What a shock to look under...

By now I feel like a candidate for the Darwin Award! Let me begin: about a year ago I decided not to change my Black 66 Barracuda from an automatic to the 833 4spd that came in the van I bought for the 318 4bbl engine - it was a B-Body trans. I bought a 904 out of a 75 Valiant 318 car along with...

Anyone know the bolt size going through the mount up into the trans case? Looks like 7/16 - 14 thread but how long? Went through some of the bags of bolts I got with the car, no luck.

Took a load to Virginia Thursday. I ran down route 522 from Hancock, MD to I-64 in Virginia. Saw a clean and solid looking white Gold Duster on the left heading south. Sorry, no mile markers and it was out in the country. Nice road for a Sunday "Duster Hunt" ride.

I looked at a built 225/ today. It has a Clifford 4 bbl intake, true split headers and is supposed to have the head shaved and bigger valves. No carb but it had a Holley 650 on it when it was in a 70's Dodge shorty van. Motor was built about 20 years ago but has less than 800 miles on it. Been...

OK! I have a 318, 360 heads, comp cam, edelbrock intake and Holley 650 sitting in the engine compartment of my black 66 Barracuda. Car is manual steering with 904 trans. Been researching headers - most of you say long tubes are a pain in A$& to install. Talked to Sanderson today about their DD7-...

Anyone here running Sanderson Blockhugger Headers? Have been looking here for a set of headers for my 66 Barracuda. Only response so far has been for fender well units - don't want to cut up the car. Others have noted full length are just a royal pain in the A$& to install. A friend of mine who...

Learning as I go!!! I was given a set of "A" Body headers thinking they would fit any "A" Body car. They came off of a 340 Demon - I need a set for a 66 Barracuda. Anyone need these headers? Anyone have a set that WILL fit a 66 Barracuda?

Anyone know a GOOD source for a new rear window rubber for a 66 Barracuda?

I have 2 diagrams from 2 different members showing conflicting information on this subject. One shows B going to the + side of the coil and C going to the - side. The question is with the W and G connections. I have a black wire coming from the distributor into a moulded plug to a female end and...

Ready to put the shocks on my Black Barracuda. I went thru all the boxes of "stuff" I got with the car - can't locate the rear upper mounting studs, bushings, washers and nuts. Anyone got these in good shape or a source for new ones?

About ready to fire the 318 in my Black Barracuda. Awhile back I printed out a diagram for an electronic ignition set up using a 4 terminal GM HEI module. It shows the dizzy wires going to the the W & G terminals which are different sizes. I have an orange wire and a blue wire coming out of the...

Need a set of 273 Engine mounts. Had to "Borrow" the mounts from my green Barracuda and alter the passenger side to put the 318 in the Black car.

Selling a 1995 BMW M3 5spd Coupe. Rare Daytona Violet with factory chrome wheels and a dove gray interior. 112,000 mile 3 owner car. Bought new in Atlanta by a woman who only put 14,000 on it in 4 years. Second owner kept it in Florida for 11 years and I have owned it 3 Years. Had 108,000 on it...

I had to "Borrow" the positive 4 lead battery terminal from my green 66 273 Barracuda for the black car. Someone hacked it apart where it splits to go to the starter and relay. Need to replace it in my parts storage for the green car.

A friend is in need of cuttable LBP 11-3/4' diameter rotors for a 67 Chrysler 300 with 4 piston calipers. Rotors are only about an inch thick give or take!

I have been pirating parts from my 273 4-speed car to put the 318 in my Black car. Need a pair of 273 motor mounts for sure! May have a local source to replace the center sump oil pan and can get a new water pump. Also need a dipstick and tube for a 904 that came out of a 75 Dart 318 car and a...