Search results for query: *

On my wife's 75 Duster 360, it's got a Dart Sport scoop. I keep thinking about buying some grommets and cutting holes in the hood, but then before I do something that's not easily un-done try and think what the upside would be. Do people with vented scoops ever see any realized upsides such as...

I've got a 75 Duster 360 that the OE radiator is looking like it's about ready to give up the ghost. I'd live to put a radiator such as this one sold by autocity1958 on ebay ( 1966-1972 Mopar B & E Body Aluminum 26" Radiator Road Runner Challenger Cuda | eBay ) But these cars came with these...

Car I'm working on is a 75 Duster 360. (5 wire ECU w/ Dual Ballast) It has an intermittent issue that'll cause it to crank and them immediately fire off when the key returns to the run position. Yesterday I replaced the ignition switch and hoped that it would solve it as it was the last...

the pic I attached is from a thread from years ago of someone looking for them too. Has anyone ever found a source? I took the tail panel trim off to do some rust remediation and 3 of the clips broke. I tried RTV'ing them on the panel but that was unsuccessful.

I've got an issue with my wife's 75 Duster 360. (Dual Ballast Wiring) Years ago (Like 2004) I put a Mopar Performance Distributor & ECU in the car and from that day on, have NEVER been able to use a 4 pin ECU otherwise the car will crank for days, but will not fire off until the key is...

I'm working on a 75 Duster 360. (My wife's car she's had since she was 16 and her Dad built it for her) The Drivers side Exhaust Tip is flopping around and it's annoying and really make's it look like a jalopy. On the passenger side, I have the hanger shown in the pictures. When searching...

so I spent a while digging thru old threads but only found this one ( Steering Column to Firewall Plate Fitment ) *That poor guy's column previously lived thru a bad wreck*. But came across this comment in Post # 5 " It is suppose to be round just like the tube is above it. Then that short...

I spent most of Saturday morning trying to find a 2.5" ID hose to replace the defrost Duct's in my wife's 75 Duster (I just went thru this with my 74 Ramcharger and wasn't happy with the flex duct I had purchased from McMaster-Carr for that. I found lots of threads here and on other mopar...

Before putting the Cluster back in a 75 Duster 360, I decided to replace the headlamp switch as the OE unit had a failed potentiometer. RockAuto showed Standard Motor Products DS357 was the replacement. it’s slightly longer, but the fitment issue is that with the plunger installed , the knob...

I'm working on my wife's 75 Duster 360. I've always noticed that the wiper switch is a 3 speed switch, and the windshield wiper motor (has a 2 speed motor mounted to car) only has on/off, irregardless of what speed the switch is in. How can I go about identifying if the car has the wrong...

While taking the starter off to replace batter cables, the trigger wire terminal broke clean off from the starter solenoid. I’m well aware (and have a plunger & contact kit in my toolbox) that these starters are easily rebuildable. But should I junk this starter which was otherwise working...

So last week I decided to take the RPM Air-Gap I had for my wife's Duster 360 that's been in the attic for 10 years and bolt it on. Simple right? Not if you know me. I pulled everything off, cleaned up & painted bits & pieces to freshen up the engine bay to not look like such a jalopy and on...

I'm in the process of swapping a Eddy RPM Air-Gap onto my wife's Duster (Factory 360 car with A/C and Cruise) I spent a few hours searching online for proper heater hose routing last night which I finally figured out (I also have both 1975 Factory Service Manuals but they're a little generic...

I can't seem to find a source for pre-bent, ready to install transmission cooler lines. Every website I've found only shows product listings up to 1973, after that nothing. Is there a difference between the lines for a 1973 with a 340/727 and a 1975 Factory 360/727 car? The lines rubbed a...

Someone on another forum wanted some pics of the Spoiler...so I pulled it out of the attic (I've got two :) ), taped it on the car and took some pics..I figured I'd post them here so fellow A-Body guys can have them for reference.

I had the full Polygraphite PST kit installed on my wife's duster about 8 years ago (no more than 10K miles since) and while I was working on the fuel line I looked down and noticed that the Drivers Side Strut Rod Bushing was GONE! The guy that installed the Strut Rod bushing is a the top...

I'm just wondering if this is possible...I'm getting the A/C working in my wifes duster and when coming to a stop at a red light, or at idle...the blower motor comes to an almost stop as well I can see a big pull on the ammeter. I've already re-done the headlight harness, but that doesnt...

I have a set of ramcharger wheels that have been cut and backspacing reset so that the tire is moved more underneath the car (must be mini-tubbed). So i figured I'd get them powdercoated for my wife's duster (its Plum Crazy)...the powder coater did not get the color right...but these wheels...

I'm going with a steel line, not rubber. I'm going to make up a new one for my wife's duster and would like some pics on how ya'll have bent the lines and routed them. Somewhere after the Fuel Pump I've got to add in a filter...Should I put the filter right up by the carb? Any pics...

Now that my wife and I have a kiddo...the A/C is important :) I'm trying to get the A/C working on my wife's car which is a 75 Duster 360 I was told by her FIL, that before the engine was pulled for an overhaul, the A/C worked (when she was 16, she's now 32). I recently had the lines...

I am looking for a set of inner fenders to replace on my wife's car, hers are severely hacked up from years of abuse. I am looking for unwarped, rust free pieces that I can weld in that can be shipped to 78374. please email me, shank3r@ gmail DOT com -Patrick

Why did I do this to myself, I was standing in their Booth at the Lone Star Shootout back in October of 2005 and told the salseman how I would LOVE to have a new set of those R/T emblems for my quarter scoops on my Coronet R/T. He said that they didnt have any at the show but if I paid now they...

Just wanted to say hi, im a n00bert to this site. Im always looking for tech stuff to work on and fix my wifes 75 Duster 360 Current projects are to sound proof the interior and to get the A/C working.