Search results for query: *

i have the trans out of my 1965 barracuda which i think is original but i don't know how to read the numbers. purchased a 1978 318 out rv and was planning on using the 727 that came with it but now i am wanting to rebuild my 904 so i can use original shifter. just wondering if trans is 1965 and...

hey guys i just put my 318 in my car. i believe the 318 is a 1978. got ready to bolt up the drivers side manifold and it doesn't fit up to head. the down pipe is hitting the block. didn't want to screw something up which i am really good at. can i grind a little off the block to get...

just wondering if there is anybody that makes a gas pedal assembly for a 65 cuda. my floor pan was rusted out and the bottom of the pedal was rusted out were it bolts through the floor. thanks for any info casey

so i went to swap the motor mounts from the 318 that i took out of my 65 cuda and put them on my new 318 which is out of a 1978 rv and on the passenger side the mounting tabs on the motors are completely different the front has 2 holes on new motor. the old motor has the 2 holes on the back tab...

i am still looking around for bezels for my cuda. found a nos set on ebay $795 plus shipping mine will get straightened and painted first

i finally found a oil pan for my cuda. kept looking for one i didn't have to beat up with a hammer to make it fit. looks just like the one i removed from the car that had rust holes in it. just got it today so haven't put in car yet but will keep you posted. napa #CRPO9B

i am working on a 1978 318 to put in my cuda was told the motor was from a truck. the water pump has wrong outlet just wondering which water pump i need. it is a non ac car and i believe i have original radiator. will a 273 pump fit the 318 thanks for any help

i just picked up a 318 for my 65 cuda it is from a 1978 motorhome i just realized the oil pan is different. i tried doing some searches but didnt find the info i am needing. what do i have to do to change the oil pan and do i have to change timing cover or anything else. just hoping it will...

finally back on my barracuda project. after putting 1975 dart disk brakes on the wheels are out of line i loosened the clamps on the tie rod and cannot get the adjuster to turn. tried channel locks but i am worried about chewing up tie rod. would really appreciate any advice on how to get them...

finally got my cuda in the garage to put on the quarter panel patches. i noticed there was a slot in the trim inside the car passenger side just below the rear window. just wondering if anyone knows what this is for. the drivers side does not have one. thanks

so i thought i had it all figured out. i just got the disk brakes switched from a 1975 dart to my 1965 cuda everything bolted up nice and going good until i got to the sway bar. i have the tabs on the lca but realized the k member is different so i cant use the sway bar out of the dart. is there...

i am looking for a 318 for my 1965 cuda as my 273 is locked up. i know i need an la block but i was wondering if some years are better than others is a 318 out of a truck different. what 1970's cars came with 4 barrel intake. any info appreciated

i am putting disk brakes on my 1965 cuda does anybody know what master cylinder i should go with. I will not be putting power brakes on car but would like to get something that will bolt right in thanks

decided to go with disk brakes on my cuda so i bought a 1975 dart for all the parts i need. I know i need to switch out the upper control arms to get the bigger ball joints. what i am wondering is can i switch the lower parts as well so i can have the sway bar and what would the best master...

Im a brand new member as i just bought a 1965 barracuda. was going to redo the the old drum brakes but i found a 1975 dart. does anyone know if i can swap all of the disk brake components over to the cuda and is the rear end the same width, it would be nice to have the 4.5 bolt pattern