Search results for query: *

Need some advice on what paint to use to respray Rallye Hubcaps and any application tips would be appreciated as well. Thanks

Temperature gauge won't go past the first mark when at normal operating temperature. Replaced with new IVR, temperature sending unit, thermostat and when grounded pegs all the way to the far right. Not sure if there is additional testing or is the gauge shot?

Where could I find either the Gas / Temperature sending push on end wire piece. Could I use the condenser wire(pic attached) which is mounted to the back of the instrument cluster? Thanks.

Looking to replace my gas sending unit for 1967 Barracuda in Canada and was wondering if anybody has had any luck with a particular brand. I have researched here and other forums with different opinions. Does Lordco, Napa or the dealership sell a premium sender. Thanks

Was wondering if the round snubbers are correct and the right placement for them. Thanks!

Cruising in the 67' Barracuda...pulled into my buddies driveway and died? Would only keep running if I had the key engaged for awhile, which is not good for the starter. Waited for a couple of minutes and would started right away and drive. Ignition relay switch? Thanks in advance.

I have a 1967 Barracuda with a rebuilt 273cu. motor bored .30 over(might be in the low to mid 200hp), edelbrock intake, edelbrock performer 1406 carb, Comp Cams Hi-Tech 5/16 .500 push rods, Ultra Pro Mag rockers, Edelbrock Perf plus hydraulic cam and lifter kit(RPM range idle-5500), headman...

Nice sunny day to take the Barracuda for a spin, the garage temperature is 9C / 48F and outside temperature is -5C / 23F. The temperature and oil gauge goes off to the far right while the gas gauge does not make it past the E. Drove the car for an hour and everything but the gas gauge works...

Was wondering if this is the right positioning for the seal to be installed(bottom portion of trunk pictured). Thanks

Converted from a 2 barrel to a 4 barrel setup with an Edelbrock performer 1406 series carb and intake manifold. What I have read is to get the throttle bracket(Mancinni Racing) and Trans Kick Down Cable Kit(Lokar). Is this the way to go???

Can anyone post pictures of the spare tire hold down set up? I believe there is a 1) coupler; 2) threaded bolt & 3) wing nut Cheers!

Going to install the trunk weatherstripping seal and was wondering if the crease goes at the bottom when you join the two tips together. Any tips for installing with door surround gasket(screw the triangle piece in, put 3M glue along the door and push-in the plastic clips into the holes and hold...

Has anyone installed the rectangular tips for the 68-69 Barracuda / or Dart on a 1967 Barracuda with the round cut outs?

After 14 years of pain & gain it is nearing the end and is being driven. Thanks to all of the FABO members who have provided the much needed info for me to get the job done!

Any ideas how to install the roof rail chrome and door pieces? I am thinking of using dish soap and water to lube it up?

Yes I am sorry another tire size question, but would appreciate some advice on tire sizes that are specific to the 67-69 Barracuda with a standard 14" rim. I currently have P205/70/R14 all around. The FABO archives threads indicate P205/70/R14 upfront and P215/70/R14 at the back(1968FormulaS340...

The instrument lights are partially working with the right side out(fuel; temperature..). The bulbs and fuses are good and the ones that are working are dim?

A wire attached to an electrical balist came off and wondering where it goes? It is attached to the instrument cluster closest to the heater on/off controll.

Was wondering if the front license shield / bracket mounts flush to the bumber tabs or on top of the tabs? 14 years apart = forgeting where things go!

My mechanic has installed an MSD coil and distributor and my tach is not operational? Is this an easy fix?

I have been restoring my car for 14 years and now I see that there are some mystery holes for an emblem behind the front wheel and to the bottom. I believe the previous holes were filled up and there are two Penta star emblems to go on? Is this period correct for the 1967?

Trying to mount the new rear bumper to the new rear 1/4 panel and it is very tight. Minimal to no gap! I guess I could try to shim it? Any suggestions?

Installing bumpers on my 67 Barracuda Fastback and not sure of the procedure to install them: 1) install brackets on car first then bumpers or 2) install as one unit(bracket & bumper together)? and are there foam gaskets which separate the bracket from the body. Thanks!!!

Does anyone know if the seat spacers sit on top of the carpet or placed under?

For the 1967 Barracuda there are 7 moulding holes on the upper & lower area of the trunk. But for the clips they give you 6 per moulding? Are there different clips for the ends?

Anyone out there can confirm if the 67 Barracuda dashpad from PG Classics has the correct original crease along the the top? The same lady which answers the calls is the tech person as well....awesome customer service...NOT!

Can't find the metal clips(1 7/16) which attach the chrome strips inside the fastback cargo area. Any suppliers or alternative clips?

What is the correct way to install the cargo carpet in the rear section of a barracuda fastback. Originally it was wrapped over the lip and then the piano hinge/folding divider panel installed over. This would appear to interfer with the hinge?

Re & re'd my speedo and took it apart. Was wondering if I put the spooles back properly. When it was in the car the trip odemeter was not working?

How do you remove the mirror(glass portion) from it's mounting base with the attached adjusting wires?