[FOR SALE] 67/68/69 FB Barracuda body/Parts

[Treblig]

From Corpus Christi, Texas I have one 67/68/69 Barracuda body with a few other parts. If you see it in the pics then it's for sale. I am willing to chop this body into enough pieces to sell it all and ship by bus in most cases. The front end, fenders and frame rails are sold and delivered. Trans mount and floor are sold and delivered. Steering column is sold as well as console and AC/heater. Dash has been cut around radio area. But all the rest of the body is there and in pretty good shape. We had no need for salt on our roads in South Texas so this car doesn't have the usual rust. The paint job on the car is over 8 years old and it has been sitting outside for all that time and you can't hardly see any rust at all.

Doors - $80 stripped clean (cheaper to ship that way)
Rear window trim - $250 (pretty nice with a few small dings and scratches)
trunk lid - $100 pretty sure it's a 68 because it had the upper and lower trim on it. Trim is bad. Also trunk has had some repairs in the grey paint area in pics but the important pinch weld area (bottom rear) below the lock has no rust!!!
roof - very nice $150
Pillars - nice $75 each
rockers - very little rust $75 each
quarters - $125 each, some small repair areas but very fixable
roof to quarter transition (rear) - $60 each
trunk pan complete - minor surface rust $125 (cut to your specs)
Rear valance - $125
tail light area - $50 each
rear rails - $100 pair
7 1/4 rear - $75
trunk hinges w/springs - $75 pair
hood - $100
Anything else just ask
ALL PARTS PRICES ARE PLUS SHIPPING!!

Or you can have the whole thing (minus the rear window trim and rear glass) for $650!!! PLUS SHIPPING
Many more pics available. REASONABLE OFFERs ENTERTAINED!!!
Treblig

 

[Treblig]

PM on reverse lights answered.

Treblig

 

[RedFish]

OOPs nevermind. Good luck with sales

 

[srixon4406]

Pm sent

 

[Treblig]

Pm sent

PM answered, thanks, Treblig

 

[Treblig]

MOre pics...

Treblig

 

[Treblig]

Still have many body parts, rear 1/4s and trunk pan are sold!!!

 

[Treblig]

Driver's rear pillar sold pending payment.

Treblig

 

[67cudafb]

View attachment More Cuda 017 (500x342).jpg

View attachment More Cuda 018 (500x373).jpg PM sent this is what I need. Price with shipping to 32656? Thanks Bill

 

[Treblig]

View attachment 1714731174

View attachment 1714731175 PM sent this is what I need. Price with shipping to 32656? Thanks Bill

All PMs answered. The Cuda is quickly disappearing!!

Treblig

 

[moparmat2000]

Where in South texas are you? I am interested in some parts.
PM sent.

 

[Treblig]

Where in South texas are you? I am interested in some parts.
PM sent.

I'm Corpus Christi.

Treblig

 

[Treblig]

Rear passenger tail light bucket/body section sold pending payment.

Treblig

 

[Treblig]

Posting pics for "69fastbackfish".

Treblig

 

[68original]

PM sent on deck lid and rear window trim

 

[Treblig]

Pics being posted for "67Commando". 18 inch, 7 Blade fan no clutch. Shroud is not in usable condition.

 

[Treblig]

PM sent on deck lid and rear window trim

PM answered.

Treblig

 

[Treblig]

These pics are being posted for 69fastbackfish:
The holes in the front of the windows are for the hard felt guides. They are pressed or attached to the window using the holes at the top and bottom. It makes it difficult to remove the window from the vent channel because you can't just pull it out of the channel, you have to slide it out the end very carefully or you break off the felt runners. If your glass is missing these I have no idea where you get new ones, they seem to be permanently attached. As you can see, this driver's glass is missing one although it's probably in the bottom of the door and could be siliconed back in place. Without these felt runners the glass would probably not slide up and down correctly. There's also a thin hard plastic film attached to the felt runners as you can see in the pic. The hard plastic probably helps the window slide easier and with less friction. Hope this helps.

treblig

 

[Treblig]

More pics as the Barracuda disappears before you very eyes.........

Passenger tail light bucket sold, hood hinges sold, driver's regulator sold, driver's b-pillar sold, rear quarters sold, trunk pan sold, trunk lid sold. Some of these are pending payment.

Treblig

 

[sleepyhead416]

jack mounting brackets & hook

 

[Treblig]

jack mounting brackets & hook

Let me check on that. The mounting brackets are attached to the part of the 1/4 panel I removed and sold but I still haven't shipped the 1/4s yet and the person who bought the 1/4s doesn't need the jack mounts (I don't think). I also think I have the hook?? Will get back to you next week.
Thanks,
Treblig

 

[Treblig]

Radiator pics for Younggun86.

Treblig

 

[Treblig]

Member who had said he wanted the trunk lid just backed out for lack of funds. So the lid is up for sale again.
trunk lid - $100 pretty sure it's a 68 because it had the upper and lower trim on it. Trim is bad. Also trunk has had some repairs in the grey paint area in pics but the important pinch weld area (bottom rear) below the lock has no rust!!!

treblig

 

[67cudafb]

Hey Gil received part and left you a positive feedback. Thanks Bill

 

[Treblig]

Hey Gil received part and left you a positive feedback. Thanks Bill

Thanks "67cudafb". I have sold many, many items with only one complaint. The one complaint I immediately returned the guys money and paid for shipping back to me and sold the item to someone else. But no one has left feedback except you, although I have had many PMs thanking me and saying that they were happy with the parts they bought.

Thanks,

Gil