[WANTED] Looking for 360 engine, 71 -74 casting number 3418496
- Thread starter Shayne Dysart
- Start date
-
- Status
Dartnut
Don't hate me because i'm beautiful
I might have one.
How complete do you want it?
Long block, short block, just the block itself?
I have several cores of many years, probably 10 or so.
I also have several 318s if that is an option to you as well.
But the shipping would be a killer. (just so you're aware of this)..........
How complete do you want it?
Long block, short block, just the block itself?
I have several cores of many years, probably 10 or so.
I also have several 318s if that is an option to you as well.
But the shipping would be a killer. (just so you're aware of this)..........
Shayne Dysart
Active Member
If you could check that would be appreciated...let me know what you have....I'm open to all options
Dartnut
Don't hate me because i'm beautiful
I'll check for you when i get back to my property in B.C., it might be a few months if you can wait. (snow covering everything)...........
Do you want just the block, or what level of completeness do you want it?
Last edited:
Shayne Dysart
Active Member
Darnut, Complete 360 would be best, however long or shirt would work too...I am in no rush so a few months would be fine. I am from Victoria so shipping to there will probably be the plan...Just let me know what you have, thx.
Shayne Dysart
Active Member
Toolmanmike, thank you for the thread change this is all new to me....when I owned a 1970 Duster in high school you just knew a guy who knew a guy....no emails or threads just a telephone call to get parts and pieces ...so thx Shayne
no problem. Hope you find what you need.
Dartn440
Well-Known Member
Shipping from US would be the same whether it is a core or a built motor. Something to consider. My advice is if you buy a core and are having it shipped spend the extra and have the seller take it to a machine shop first. No you aren’t going to get a motor for $300 but you ARE going to get something you know you can build. I have bought a lot of cores that end up having scrap blocks or heads and end up becoming parts motors for something else. They are out of their homes for a reason. Same goes for the ones that were running when parked....running yes....but that knock though? Lol
Shayne Dysart
Active Member
Thank you for the good advice, totally makes sense to have a little work done before shipping....better to know before hand. Will do. Southern Pines...nice I have family in Pinehurst..
Shayne Dysart
Active Member
Mbaird, thank you I am in Toronto, but have family in Victoria if you could check numbers that would be appreciated...
Dartnut
Don't hate me because i'm beautiful
I will see the next time i'm there.
Shayne Dysart
Active Member
Nice, beside the casting number shown it says 360 correct. What else do you have with the block or just block?
Shayne Dysart
Active Member
Question, why is the block not in a car and can you also send a couple more pics...inside cylinders etc. thank you
its just an extra block I have sitting at a friends house.
I do have a nice 360 crank ,Rods and pistons that came out of a low mile Motorhome block that I used for my stroker.
But if all this stuff needs to be shipped to Toronto it seems cost prohibitive.
I do have a nice 360 crank ,Rods and pistons that came out of a low mile Motorhome block that I used for my stroker.
But if all this stuff needs to be shipped to Toronto it seems cost prohibitive.
Shayne Dysart
Active Member
Thx for the follow up ...any idea what the block and crank might weigh...is the crank cast or forged? let me do some digging into shipping and I'll get back to you. Thx
Shayne Dysart
Active Member
BTW how much do you want $$
Shayne Dysart
Active Member
Does that $ include Main Caps and crank ? Ok thx let me look at shipping options and I'll get back to you
Shayne Dysart
Active Member
Mbaird reached out to USHIP to check pricing, should find out in a few days what the cost will be to ship in my direction.
- Status
-
Similar threads
