NOBODY DOES THIS: Edelbrock Heads on a 318 Mopar—Will It Work? Project "Mission Impossible"
- Thread starter 273
- Start date
-
? Smallest bore? Nope.
Last edited:
Close, He's a clueless Ford guy
oh would you look at that... if you spend 2K on a set of heads all of a sudden it becomes "Mission: Possible"
smdh
smdh
PRH
Well-Known Member
How much magic dust does it take to transform old factory stuff into shiny new Ede stuff?
This project went way off the rails years ago.
This project went way off the rails years ago.
4eighteener
Well-Known Member
At least he gave a shout out to Tim at 318will run
Raffle off the engine for St. Judes is a good thing.
MOPAROFFICIAL
If it has tits, it's a liabilititty.
Clickbait.
This thing became "mission disposable" long ago.
I believe people were chasing algorithms when it began...$$$$
Last edited:
Mopar44134
Well-Known Member
It’s nice to something different. Sounds like all you haters are missing uncle Tony lol. There was a shout out to Mopar Joe.
Icetech
Well-Known Member
fuckin hell... that is a useless video, he could have searched for 10 seconds and known the heads fit fine...
He's a nice guy but never forget he put $7000 heads on a small block ford with a tunnel ram and got beat by a 318....
He's a nice guy but never forget he put $7000 heads on a small block ford with a tunnel ram and got beat by a 318....
MOPAROFFICIAL
If it has tits, it's a liabilititty.
Most of the people on YouTube don't know much more , as much, or sometimes even less... than anyone you would meet at a car show parts swap.
I have trouble watching many.. because it feels like a show n tell of part$ and ego/persona more than a lesson or helpful tip/secret.
What I've seen lately are guys attaining notoriety or views via calling out other YouTubers.
The vac debate... what a crock of sht to watch that was.. guys who run manifold vac vs guys that don't.
What are they truly accomplishing by using manifold vac that they couldn't tune the carb to optimize.. fkn hell...
I have trouble watching many.. because it feels like a show n tell of part$ and ego/persona more than a lesson or helpful tip/secret.
What I've seen lately are guys attaining notoriety or views via calling out other YouTubers.
The vac debate... what a crock of sht to watch that was.. guys who run manifold vac vs guys that don't.
What are they truly accomplishing by using manifold vac that they couldn't tune the carb to optimize.. fkn hell...
Last edited:
It is what it is. Garbage content. Unfortunately here we are, feeding the algorithm by talking about it here.
Remember, if something is free (YouTube), it's because YOU are the product being sold.
This is garbage content and I'm not going to reinforce it further by bothering to click on it.
Remember, if something is free (YouTube), it's because YOU are the product being sold.
This is garbage content and I'm not going to reinforce it further by bothering to click on it.
Some act like these guy's are rolling in dough from youtube and soul purpose is clicks at any cost, yes most know 2.02 fit in a 318, but some don't, even on here, but not why I posted it, some are interested in mission impossible and thought they would like and update.
The video didn't tell much. No "how to". Build an iron head engine then re cam and heads with the Edelbrock's? Is that what's planned?
To be honest I only skimmed through it, if it ever makes it to a dyno
I'll be interested in the results.
MOPAROFFICIAL
If it has tits, it's a liabilititty.
First of all they're not your videos, so don't take it personal. ..Secondly , no one thinks theyre rolling in dough, if they were.. they wouldn't bother with it.
Sooner or later everything turns into a popularity contest ...and we all know how that goes and what it turns into.
Competing is always beneath the surface
-
Similar threads
