Stop in for a cup of coffee

[halifaxhops]

Flex seal let me down, so did duct tape.

 

[ScampMike]

oh - I remember the cracked trans - didn't realize you were at the point of installing the driveshaft 'tis all

Boy you are not with it today. Yes the Popmobile, cracked the trans in half.

maybe I'm not the the only one not with it this morning - LOL

whoa! cracked trans? the new one?

you haven't missed anything... :twisted:

Cool, never been there Mike :coffee2:

 

[GeorgeH]

I think a little JB Weld and a buffer would have got her all fixed up...

X's 2 lol

 

[halifaxhops]

Trans is still on the floor. Just standing around looking at it and doing other little things while it is out. Like a driveshaft loop!

 

[ScampMike]

brakes and all?

Got it done finally, crappy cell pic

 

[memike]

Got it done finally, crappy cell pic

Very nizze George :glasses7:

Looks nice George.. Can I borrow it???

No !! I am

 

[halifaxhops]

Very nizze George :glasses7:

No !! I am

I am closer!

 

[zkx14]

Hey hey hey I hit 10K!

And over 3/4 of it is this thread... :coffee2:

 

[halifaxhops]

And over 3/4 of it is this thread... :coffee2:

Aint that the truth!

 

[GeorgeH]

Trans is still on the floor. Just standing around looking at it and doing other little things while it is out. Like a driveshaft loop!

never seen one split open like that

 

[halifaxhops]

never seen one split open like that

Funny thing the innards look fine to me.

 

[GeorgeH]

brakes and all?

yup! new brakes, bearing, new tires, new breakaway battery and switch, painted wheels and trailer, and have some new DOT reflective decals to go back on it. It needed some work, been sitting for the last 2 years.

 

[halifaxhops]

George, what did the diamond plate set you back?

 

[GeorgeH]

George, what did the diamond plate set you back?

It was on there when I bought it 12 years ago. All I did was clean up and paint what was there.

 

[halifaxhops]

I was looking at them a while ago for my small trailer and they are really expensive here, I think it was 460 a sheet.

 

[Ben Drinkin]

I've been cleaning up my rear end. Wire wheel on a grinder was having a hard time getting all the crap off. There were a few places I couldn't reach. Might have a buddy take a look at it and see what he can do. On a better note, The inside of my rear end looked really good, especially considering how old it is. Plenty of lube left in there.. I'd post pictures but I couldn't get my cell phone to take a very good picture...

 

[ScampMike]

hey George - what are you hauling on that trailer?

 

[GeorgeH]

I was looking at them a while ago for my small trailer and they are really expensive here, I think it was 460 a sheet.

$460 for a 4x8 sheet?

 

[halifaxhops]

That was a quote I got when I was looking on 3/8 aluminum.

 

[ScampMike]

yea butt... :butthead: :twisted:

I've been cleaning up my rear end. Wire wheel on a grinder was having a hard time getting all the crap off. There were a few places I couldn't reach. Might have a buddy take a look at it and see what he can do. On a better note, The inside of my rear end looked really good, especially considering how old it is. Plenty of lube left in there.. I'd post pictures but I couldn't get my cell phone to take a very good picture...

 

[halifaxhops]

Man I just googled diamond plate up to 795 now!

 

[GeorgeH]

hey George - what are you hauling on that trailer?

that trailer has had tons of crap on it! lol From several Harleys, tool boxes, of course cars, to living room and bedroom suites. lol I really bought it originally to move my toolbox around. I got tired of paying a rollback $300. because it's a "special load" as they call it.

 

[ScampMike]

yeow.. I was thinking I was going to put some on the floor of my trailer...

 

[GeorgeH]

Man I just googled diamond plate up to 795 now!

is that shipped? it just seems way outta line

 

[halifaxhops]

Delivered, just clicked on a company out of NJ. They go to Harrisburg daily. I am not getting it was just checking the price.