About the same here,60” 3 point mower behind my little old Kubota diesel tractor. You are going to find the 11’ is going to shave a lot more than that off your mowing time. I used my son’s 10’ mower, less than 1/2 the time.
Stop in for a cup of coffee
- Thread starter toolmanmike
- Start date
-
zkx14
Duster De-ruster
Good morning all.
Does seam like a great deal, but definitely want to be sure it will work. A lot of the old stuff is open cell and does absorb water. Cold storage dock doors were metal clad foam and would get so flippin heavy, springs couldn't be adjusted anymore and have to replace the door. That would be obvious just moving a few pieces. The raised patterns could make for a cool looking shop interior, (or could be a nightmare to line up in any way that made sense.lol) Even the ends of the full panels look like they might be patterns. Also, you could end up paying more to get rid of the scraps then the whole mess cost you...
zkx14
Duster De-ruster
I'm goin with
Good evening all of you good folks in America. And good morning. Lynda and I are going out to dinner now. Out on the town..
I think it is best for Wolfies son to check first. I would need at least 80 depending on size...........
Shop is 40x60 14' wall height..............
There was a guy in Somerset PA which would be closer but I cannot find his ad. That would be closer. How much are they asking per sheet?
I posed this question to Chris yesterday since he has similar wheels..............
The issue I am having with the front Cragar is that 4 lugs go on fine and 5th, doesn't matter rotating tire, etc. Washer will not sit flat on the face of the wheel always. I have to crank it on, shouldn't have to do that, just doesn't feel right. I wonder if the issue may be due to a larger hub from stock?
Lugs and wheels
www.summitracing.com
www.summitracing.com
The issue I am having with the front Cragar is that 4 lugs go on fine and 5th, doesn't matter rotating tire, etc. Washer will not sit flat on the face of the wheel always. I have to crank it on, shouldn't have to do that, just doesn't feel right. I wonder if the issue may be due to a larger hub from stock?
Lugs and wheels
Cragar A-KN2121 Cragar Keystone Klassic Wheel Lug Nuts | Summit Racing
Free Shipping - Cragar Keystone Klassic Wheel Lug Nuts with qualifying orders of $109. Shop Lug Nuts and Lug Bolts at Summit Racing.
Cragar 61C5451220 Cragar 61C Series S/S Super Sport Chrome Wheels | Summit Racing
Free Shipping - Cragar 61C Series S/S Super Sport Chrome Wheels with qualifying orders of $109. Shop Wheels at Summit Racing.
$300 OBO for everything...................never seen anything cheaper.
zkx14
Duster De-ruster
All other ones I have seen are per sheet and was still a couple thousand dollars................................
Yeah...can't beat that
Mine is 45x43. Just need ceiling tiles. To me the whole shebang I wojld like to have 500 into it. Let me contact Gauge (yes thats his name)
Here
I have a few trailers if needed
They are only asking $300 OBO for everything..................you can pay them $500 if you want.
No that would be shipping also if your into it? Sent the guy a message if it is all patterned.
If there is any left over I can use a few sheets
Have to measure it again but 45x43 will cover it have to do the math. Some how coming up with 63 sheets that has to be wrong. I think when I did the math last time it was around 30.
Depends on the sheets, if they are 4x8 or what.....................
on 4x8 sheets says =83 for me
zkx14
Duster De-ruster
What pattern do you have on the car? Those wheels show 4.5 The washers with that lug kit are variable, but can only be used on wheels with the inset holes they drop into.
No word yet if the guy to help me with the lash is coming today or not.
What did you do for the math? Cannot believe I forgot how. Did 45x45 then divided that by 32?
-
Similar threads
