And that only cost you $1,000.
Stop in for a cup of coffee
- Thread starter toolmanmike
- Start date
-
ICE!!!
Icetech
Well-Known Member
Other than in a straight line, brieflythat would be horrible to drive
@Icetech
Getting everything staged and completely re- running and shift, park and speedometer cables was a solid move. Much cleaner runs and better clearance around the down pipe. One of these days I'll need to rework the brake lines from the master cylinder to the distribution block. Not super happy with it.
Getting everything staged and completely re- running and shift, park and speedometer cables was a solid move. Much cleaner runs and better clearance around the down pipe. One of these days I'll need to rework the brake lines from the master cylinder to the distribution block. Not super happy with it.
Icetech
Well-Known Member
my cable only run one way.. sounds like you are getting close
hope it goes well
Start and finish, yes. It was the routing around that busy part of the engine bay below the master cylinder.my cable only run one way.. sounds like you are getting close
Mattax
Just the facts, ma'am
Icetech
Well-Known Member
Love it
25 bucks is 25 bucksAnd that only cost you $1,000.
abdywgn
dismantler
wasn't that a magazines project vehicle? black with flames on the nose?
abdywgn
dismantler
did a timing chain in my 340 about every 6 months. should have bought the good Cloyes set but went with the stock replacement type. I would use yellow death weatherstrip adhesive and glue the timing cover gasket to the timing cover and the water pump gasket to the water pump. on the gasket that went to the mating surface, I used a yellow Valvoline grease. never used silicone...I had bought a 383 from a guy and he used so much of it on the timing cover, it was on the chain and gears. swore off it at that point. yes, my set-up would "weep" oil at spots on the timing cover but didn't leak water.k.. timing covert gasket kit ordered.. hopefully i can get this apart and back together pretty quickly... this is where i wish i had used less silicone
Icetech
Well-Known Member
i use a VERY thin layer i smooth with my finger on both sides of the gasket.. so it doesn't press into the motor.. i just hate leaks and can't not glue things together...
And yeah.. a good timing set is worth it.. mine is a Trick Flow billet set $99
abdywgn
dismantler
can't find the one I want but smiley with it's fingers crossed
Icetech
Well-Known Member
well.. i already replaced it... so.. hoping i can sell it to make some money back..
I just got back from grocery shopping and the only thing I got was a bend over and hand me your wallet.
Icetech
Well-Known Member
Yup.. just read an article from the USDA that meat is going to keep going up for the foreseeable future also.... WINNING!!! don't look at your receipt... the news says you are paying less.
Was trying to get my hair cut before I left for MITP but 5 times that I tried the 2 Barber shops were closed. It's a 100 mile round trip to get to the closest Barber.
Looks like I'm going to the car show with long hair.
Looks like I'm going to the car show with long hair.
Icetech
Well-Known Member
Was trying to get my hair cut before I left for MITP but 5 times that I tried the 2 Barber shops were closed. It's a 100 mile round trip to get to the closest Barber.
Looks like I'm going to the car show with long hair.
Bah.. nature made me not worry bout hair bout 20 years ago.. but i enjoy just shaving it down and be on my way
saving money on haircuts too!
Sure just believe and still bend over.
Icetech
Well-Known Member
This is what people wanted.... it's odd they get upset by it now
(not you, just people in general)
You didn't have a "Buy 4, get one free " for the blueberries that are 3 hours away from rotting molds?
-
Similar threads
