Search results for query: *

Any one put a gear vendor unit in 70 Duster. If so any modifications needed to make it fit. And does anyone have one for sale. Thanks

What is best type of shock for street strip with leaf springs on 70 duster.I have read not to use gas filled.

Need to make sure my rear shackles that hold leaf spring is adjusted correctly. One looks like its at a 20 degree angle towards rear bumper other is almost straight up and down. How much of a angle should be on them towards the bumper. Sitting high on one side .It is on a 70 Duster

I mounted a trans cooler in front of my radiator. It runs about 10 degrees hotter in traffic now. Should I have a space between the cooler and radiator ? It is flush against the radiator now. Or can it be mounted some where else. Its in a 70 duster 340

Have a loud high pitched whining noise coming from rear of car . Gets louder when I give it the gas. Nothing is rubbing and pinion nut is tight. Any ideas what it may be? Thinking it may be pinion bearing

What is a good after market posi unit that is better or compatible with the 8 3/4 unit. Any suggestions

I have a 727 trans. I am checking the fluid with it warmed up and in neutral.If you pull out the stick it shows full on the front of the stick,but the backside of the stick has no fluid showing on it.Is this normal or do i need more fluid.

Any one have a bolt in drive shaft loop from us car tool in a 70 duster with 3"exhaust.Thinking of purchasing one.

I recently had a torque converter built for my car.I spoke with 4 different companies which i will not name.Some of them could care less if they sold you one or treated you like crap.I had two built that was way to much stall that i had to take back out .The only one i will ever deal with is...

Just had trans rebuilt.It is a 727 with a turbo action 3000-3500 stall. In auto driving normal 1 to 2 shifts quickly can barely tell it shifted 2to 3 is fine.When i manually shift from 1 to 2 at lets say 1500 rpm it feels like you hit the brakes then goes on. 2 to 3 manually shift is fine.Can...

Could someone post some pics of bouchillon kick down assembly using a holley carb .i believe i have it right . Any help would be greatly appreciated

Bought pennzoil says dex/merc on it.For use in vehicles previously servicable by dexron-lll & mercon brands.This is going in 727 trans with 3500 stall newly rebuilt.Did mopar used to use dexron lll.Hope this is the right stuff.

I have a rebuilt 727 getting ready to install.How can you check the 3 prong neutral safety switch.I have a meter to ohm it with but dont know what pins should have continuity when in park or neutral

I am having a b&m shift enhancement kit put in a 727 trans.Would this have the low band apply since you are using the original valve body and not replacing the valve body

Does anyone run a converter from precision converter company in Ohio.

Anyone running a 10" coan converter in a street car, how do you like it

Can anyone tell me what parts are needed to rebuild 727 trans.I have a 500 hp 580 ft lb torque 340 what parts would you suggest to get.I want the parts to hold up no matter how i run it .I would rather have over kill than not enough tired of taking this trans in an out.If i buy one i want to...

Anyone use 727 specialist located in Indiana.Or any good transmission places in ohio

Had problems 1st to 2nd shift last summer after trans rebuild.Ended up being valve body.Installed cheeta forward shift valve body with bouchillon cable set up.No problems the rest of the summer.Drove the car the other day trans working fine.Drove it about 20 miles and no second gear straight...

Can someone tell me what the u bolts torque at on a 70 duster with espo heavy duty springs.

Changing 391 pig to 323.Both are 741 housings.Has green bearings.Bought 741 case with 323 gears.Put pig in axles like about 1/4 of inch from going in .Seems like axle race is tilted out at the bottom more like they are in at an angle.The guy supposedly removed what ever it is in the pig that...

Where can you get bolt in drive shaft loop for 70 duster with tti 3" h pipes.

Have 727 trans that has been rebuilt with cheeta forward valve body.I need some advice on a couple of things.I adjusted the cable to get the shift points where i want.That seems fine.I think the 1st to 2nd shift is soft. 1-What controls the 1st to 2nd shift and how hard it shifts 2-What do...

Anyone have a photo they can post of boucillon kick down and throttle cable installed on holley carb

Has anyone used auto zone atf+4 in 727.Did it work ok

Is there any markings or numbers to idenify what stall i have that came in my 70 340 duster? It is out of the car

Where can you buy the correct socket to adjust the front and rear bands on 727.

Any suggestions on kick down cable assemblies for 727 trans other than lokar or original

I have a 727 trans with lokar kick down cable.I opened the throttle to wot and pulled the lever on the trans all the way back and hooked up the cable.The trans shifted fine.Now it shifts softer from 1-2 and 2-3 also revs a little before going from 2-3.Where should the arm on trans be at idle.If...

Have rebuilt 727 with everything new .Drove it about 120 miles felt it slip a little when it went into third gear.Was working fine before that.Took it straight home and checked the fluid which was okay.Have not been able to speak to trans guy yet.Any ideas on what the problem may be