Recent content by brokengarage

  1. brokengarage

    Couple of questions on sheetmetal/bodywork

    See recent article in Mopar Muscle. http://www.hotrod.com/how-to/paint-body/1509-how-to-aligning-mopar-body-panels/
  2. brokengarage

    SRT8CUDA Build

    Like mentioned, I would call them. They made a rear quarter glass (tinted) for my 68 fastback.
  3. brokengarage

    Pulley Question

    According to a pocket book I have on pulleys, the 59 to 69 small block single groove crank pulley for a cast iron water pump has the following measurements. OD 6 and 3/16", OD HUB is 4", Length or height is 1 3/4" and takes a belt size of 17/32" so the pictures look correct.
  4. brokengarage

    Mounting msd box

    I don't think you can use the larger rubber mounts they sell so I used some smaller width plumbing washers between the 6a and the inner fender. Been running it for years with no problems.
  5. brokengarage

    Mounting msd box

    I have a 68 barracuda and my 6al box is under the battery tray and the bracket that bolts to the inner fender and to the tray itself is in place. I slid ur in under the tray to figure out placement but then had to remove the tray and brace to mount it. Mine mounts with 3 small bolts through...
  6. brokengarage

    OEM Battery

    I bought one from these guys 8 years ago for my 68 Barracuda. Keep a Battery Tender on it and it still starts the car fine. http://shop.turbostart.com/Collector-Car-Series_c2.htm
  7. brokengarage

    which door glass will work on a convertible?

    You might try these guys to see if they can make you a piece. I got a quarter window glass for my 68 FB (tinted). Fit just like the original. Sanders Reproduction Glass Peninsula Glass Company Toll Free 800-468-4323 ext. 203 Direct 360-892-2029 ext. 203 Fax 360-892-8152...
  8. brokengarage

    Push Button heat/ac control module

    Call Classic Auto Air in Florida. I sent one down there to be repaired (ended up being too far gone) so they sold me one they had in stock instead.
  9. brokengarage

    [WANTED] Intake Manifold Vacuum Fitting

    Thanks but not what I need. The nipple the hose would go over needs to be about an 1/8 inch in diameter.
  10. brokengarage

    [WANTED] Intake Manifold Vacuum Fitting

    I also thought about doing that, just need to find a small piece of tube. Will also check hardware store and see what might work.
  11. brokengarage

    [WANTED] Intake Manifold Vacuum Fitting

    I am looking for a vacuum fitting that would screw into the intake manifold for an a/c car. The very small diameter hose that comes from the a/c push button control and through the firewall would attach to the fitting. This is for a 68 Barracuda that was an original a/c car. It was originally...
  12. brokengarage

    Source for engine hardware?

    This sight might be of some help. http://www.amkproducts.com/default.htm
  13. brokengarage

    Craigslist tool chest find

    In the most recent TP tools catalog, that blast cabinet is $499 before shipping. I have the same one and use glass bead. Works good.
  14. brokengarage

    [FOR SALE] Top cat whiskers-66 valiant

    FWIW. I also bought a set of window felts from Restoration Specialties but for a 68 Barracuda fastback and my outers for the door were also short about 2 inches. I compared that to the 68 convertible and the convertible runs all the way. So I was like damn, what is going on here. But when i...
  15. brokengarage

    [SOLD] 14" large bolt pattern steel wheel with good bias ply tire

    By chance is it 5.5 inches wide and the center section where the dog dish would go be 10 inches across. Appears to be 9 but wanted to check.
See more
Back
Top