Search results for query: 318 cam

Chinese aluminum heads 170runners Airgap intake Roller lidters 750 carb 11.1 compression or 11.7 suggestions please 318 stroked to 392 new bottom end balanced. Purchasing from clegg. Not looking for trophies here. My thumper cam is not really adequate now. .514 int 498 int. 107 lsa. Voodoo was...

Looking for cam suggestions for my 318. It’s bored .030 with flat top pistons and I’m getting ready to put on speedmaster aluminum cylinder heads on with an air gap intake and a 600 Holley carb. 727 with 2000 stall. posted from mobile

This will probably open up a can of worms as this subject has been well covered but I am interested in some recommendations that folks have actually built and ran. Here are the particulars. Care is a 73 Dart swinger 3.23 geared 25" tires factory high stall converter in 904 with a TF-2 shift...

Having a hard time getting the answer I’m looking for, so I’m going to try this again. I’m building a LA 318 out of a 74 satellite with the most amount of stock parts and cheap mods as possible. I’m new to all this and I don’t have a lot of money to work with . I want to put a cam in this engine...

What is the biggest cam you can put in a LA 318? I saw something about you can’t put high lift cams in them without grinding down the valve stem guides. Also, what mods other than springs will need to be done?

What is the biggest cam you can put in a LA 318? I saw something about you can’t put high lift cams in them without grinding down the valve stem guides. Also, what mods other than springs will need to be done?

Hey, I have a 318 74 Gold Duster that I have a Holley 650 classic Edelbrock intake and then I have a set of hooker headers and a 2.5in exhaust. so next I'm looking for what is a good cam that I can easily street but has a good lope and a little more power. But one that does not have a high...

After learning how to install cam bearings, buying the installation tool and doing it myself for the first time, the last thing I wanted to do was to do it all over again. Overkill? Perhaps. Did it work? PERFECTLY. Not one nick, mark or scratch on the fresh new cam bearings.

I'm freshening up a 1974 low comp 318 with a quick hone, new plasma moly rings and new bearings. I done some home bowl porting & port matched the 675 heads with larger 1.88 / 1.60 valves. SCR will be around 8.5:1 with Mr Gasket 1121G (0.028") head gaskets. Using a port matched Performer intake...

Hey peeps! Anyone ever run one of these? On their 318? Been offered one of these COMP Cams 20-225-4 COMP Cams Xtreme Energy Camshafts | Summit Racing Hopefully should wake it up a bit as it's the heads and cam that let it down now. 1970 318 V8 stock bottom end Eddie performer intake Eddie...

Used 318 roller cam and hyd roller lifters out of '85 or '86 Chrysler. $175 shipping included to US contiguous. Perhaps a good candidate for an Oregon Cam performance regrind? Since no one was interested in the complete 318 I've been offering I decided maybe someone some of semi-desirable...

Will do some test with my flat tappet 318 ( 1971 year ) that is in my 68 fury III , ill run a modified 2bbl intake and run another 4bbl intake and 4bbl carb , Guy lost the cam card but its the only specs i have , bought it for cheap , with a double timing chain : i believe its a elgin or old...

Hi guys Im researching to turbo my 318 in my Aussie Valiant and wanted some advise on a cam choice. Im looking at building the following 8.5-9.0 comp Edelbrock rpm heads Victor 340 intake Holley Sniper throttle injection Holley Sniper ignition package to plug and play with the injection Im...

What's up guys? Hey so wanted to reach out to the experts here... I'm really wanting to wake up my 318 a bit. I've been researching a lot but wanted to reach out and see what you guys think. I'm debating on buying new heads and a cam to make some power, but I do have a set of old 587's that...

I pulled my cam out and the 4 bolt plate off the end and not sure if that is supposed to have a gasket or seal behind it ?

My engine builder has suggested the Comp Cams XE-250 or the XE-252. Since I'm cam "dumb" I would appreciate some guidance. Some details about the car/engine to the best of my knowledge: The machine shop performed an .030" over bore on the cylinders, polished the crank and added(?)...

New Crower Hyd Flat Tappet Cam. #31205 Fits 273-360 Engs LA. Check the cam card For Lift/Duration $200 + Shipping Western PA Pittsburgh

...I've found out, the 340 cam has a ivc point of 69* and this brings down the dcr to like 6.63:1 ( 18 psi lower cylinder pressure than a stock 318 cam ). Wouldn't this hurt performance rather than help? I based this on a 1973 318 with a 8.6:1 cr. Did I figure something wrong or have the wrong...

68/69 original 273 or 318 hydraulic cam and 12 + 2 NOS old lifters in no order (they were so clean they fell out), Very low mileage. $90 OBO + shipping from Greenwood, SC 29649

I am having my 318 rebuilt with new rings, bearings, rods, pistons etc.... The engine will have a roller cam installed and I am wondering if a high zinc oil is still required? The engine will be torque plate honed. From what I have read it should be run in on dino oil but can't see where zinc...

I've read a lot on the use of the 340 cam in the 318. With the 340 being a performance engine, wouldn't the duration at 0.050" be 228* on the intake and 235* on the exhaust? My question is, isn't that a lot of duration at 0.050" for a 318?

For the 318, would the lunati 701 be a good choice for what I'm wanting to do or the 700? I used a compression ratio calculator put in all the required information and it said that I would have a 9.40:1 CR. Is that a good compression ratio for either 1 of those cams? I don't want to have to back...

I'm looking to get a new cam for my 318 build. i've got 1.88/1.60 valves with a 600cfm holley on it. police interceptor heads. i'll be using the kb 167 pistons for close to zero deck. crank and rods are stock 74 internals. Stock bore. Stock lifters, pushrods, and rockers as well. I want more...

Hey guys I am very frustrated with this issue and it's the only thing left to do in order for me to assemble my 318. I went to Hughes for a suggested cam and they did just that, suggested. It was late September and I ordered one from Hughes. Didn't hear from them and after 3 weeks I reached out...

Just for ***** and giggles what's the biggest cam everyone has run on a stock or 90% stock 318? I bet my custom grind for my 318 magnum dirt track engine (stock except pistons flipped, air gap intake and a stromberg WWC 2 barrel carb) has everyone beat LOL. ***SPrings do not count towards the...

So I recently bought a bone stock '73 318 2 barrel. Since it is going to need to beat up on some stock mustangs from my high school, I am going to do a cam swap and put on a '71 340 4 barrel intake I got with the engine. My question is; since I am only changing the cam and intake, what cam...

I'm in the process of giving my barracuda a valve job, removing the heads and cleaning everything. I verified it has a sticking valve with a piece of paper getting sucked to the exhaust test. The engine was ran with a badly rusted gas tank and red particulate for a while which I blame for bad...

318 magnum cam 432 lift single pattern / timming set single row , chain stamped made in usa / valve springs,retainers,locks. all were new in remanuctured motor by ac/delco. Motor never run, I installed new cam setup in motor $190.00 or Best offer plus shipping or seperate cam and springs...

I'm looking for a roller cam from a pre-magnum 5.2 (.432 lift) to put in our 5.9. Anyone got one laying around?

So I bought a re-ground, long snout roller cam off ebay a couple years ago because the price was so cheap and I thought it would work ok in a 360 magnum. Well I came across a really nice 318 magnum for cheap and bought it just to get my car moving again. So I guess I just want to know how...