Search results for query: *

Looking for a passenger side front splash shield for my 65 Cuda that is in good condition Without rust. I live in normal Illinois 61761. This is one of the last pieces I need to make the car complete. Thank you!

Hello everyone- I need the sage advice and wisdom from all your mopar years/experiences. I am currently replacing the 318 w/fenderwell headers in the car w/a hotter 340 (.20 over w/ported pro comp alum heads) and tti headers. The engine compartment has been degreased, freshly repainted...

Hi everyone- My 65 cuda started right up after 4 months of storage. However, once the car has ran a little or is warm, it does not to start again. Looking for suggestions. Thanks, Illcuda65

Does anyone have inner fenders for an early A body- 65 Plymouth barracuda? Mine are hacked due to fenderwell headers... Thanks, Illcuda65

Are inner fenders for 65 cudas repopped anywhere?

Anyone bought the Hughes super prepped heads? On sale now for 2065, looking for feedback as I would purchase these within the next 24 hours.

I will be doing a swap to the KH front disc on my 65 cud a. Due to the fender well headers currently on the car, the dual reservoir master cylinder I purchased is to large. Can I run my current single reservoir that I used w/my 10 inch drum brakes? Any and all suggestions are appreciated.

Hi all- I installed some LED tail lights over the weekend and during the process discovered quite a few melted wires. Due to the multiple melted wires I feel that it is wisest and most importantly safest to replace the wiring harness in my 65 cuda. I was hoping for suggestions with quality...

DO NOT DO BUSINESS WITH MARKS340!!!! HE HAS $2,800 of my money (3 years worth of savings for my car) and will not respond to any of my messages (email, PM on forabodiesonly.com, and phone call.) I have purchased quite a few items on the website- 340 motor from hemiEd, KH brakes from...

Hi all- I was hopeful someone around here knows of replacement steering column bearings for a manual steering 65 cuda..... Please let me know!

I am going to be installing a 340 soon into my 65 barracuda. I bought the 340 off of member HemiEd and am excited to make the jump up from the 318. The 340 is bored .020 and is set up w/a comp thumpr cam- long duration. I am going to pony up for the RHS heads here quickly and I would like...

I recently got the 65 cuda out of storage and unfortunately the clutch will not disengage. Not sure if this malfunction is due to 4 months of inactivity or not.... So I am looking to replace my old 10 1/2" three finger clutch setup. I will also be pulling out my 318 and putting in my new...

Need both upper and lower steering column bearings for a 65 barracuda. PM me if you can help me out! thanks, Bryan

Just need a little bit of information from the experts here on the forum. I have been looking at Edelbrock RPM air gap intake manifolds for a while. Hughes Engines is not very far away from me and they offer deep port matching on the intake. The stock intake is listed at 260. The deep port...

So I am at the body shop to pick up the car today and POOF the throttle cable is frayed....I have a 65 plymouth barracuda that has been through a couple sets of throttle cables over the years- always used/worn parts fabbed up to work. I want to upgrade and make sure that I do not have this...

I am looking into buying a different motor for my 65 barracuda. All of you experienced Mopar Mechanics please give me an idea of the value of the following motor: 1971 340 Block Ø Bored. 030 Over Ø Keith Black-Hypereutectic Pistons Ø...

Just looking for some thoughts and feedback from this very knowledgeable board. My ride ais a 65 cuda- 318, 4 speed, 3.91 gears w/6 pack hood scoop. I would like to upgrade from 10" drum brakes on my 1965 Barracuda to a disc set up. I was thinking this would cost around 1 K.... After looking...

Hi all- I'm new to the forum and I am very impressed with the level of knowledge on this board. I have a 1965 Plymouth Barracuda- 318 putting out 350 ish h.p.- 4 speed, 8 3/4 rear end w/ 3/.91 sure grip- but I am still rolling with 10 inch drums for brakes. I wanted to get everyones...

Found this site a couple of weeks ago and found it to be very insightful. I have a 1965 Plymouth Barracuda that is 95% restored w/following setup: 318 (cam, swirl port heads) 4 speed 8 3/4 rear end Viper Red w/black and charcoal grey interior I will post pics soon. If anyone knows of a top...