Search results for query: *

I need factory rear seat belts for my 71 duster. I actually have the male half so only really need the female half the side with the release button. Should be fairly nice since the car these are for has had a frame off restoration. Thanks.

I have a 71 duster and I'm thinking of adding the turn signal indicators on top of the fenders. Since my car does not have them I would need to know where to drill the holes. Where can I find some measurements?

I saw a picture of a bracket going from the fender to the firewall to add to the structural strength. I had these on my Shelby and Mustang GT. What are these parts called and where can they be purchased? What models got these?

I received a tire inflation sticker for my 71 Duster. Where were these placed from the factory? Drivers door or jam or where?

WTB - I have a 71 duster 340 without a spare tire. I need the rim and tire to place in my trunk.

I am going to install the foot pump squirter in my 71 Duster. Where is it suppose to be placed on the floor. I know near the dimmer pedal but a more specific location or picture would help. Are the holes or detents in the floor board?

Some refer to this as the horn relay and seat belt buzzer. Are both contained in the horn relay?

A general engine question, I have a 64 273 V-8 non comando engine with a 4 barrel 600cfm edlebrock carburetor automatic choke. When the car is cold it idles fine, 750 rpm, when it warms up it is at 550 rpm when the needle passed the middle a little bit and the engine is fully warmed up and its...

My mechanic feels I will get more pep or off the line performance by by having the torque converter rebuilt with a higher pounds opposed to going from 3.23 to 3.91 gears in the rear end. The car is a 64 valiant with a 273 auto, 4 barrel carburetor. I've never done either so what are your...

I bought my 64 valiant that had its rear end changed. I is a posi traction 8 1/2 seems to have 3.23 or so gears in it. I pulled the drums to install new brake shoes and they seem only 1.5 inches wide where I believe the factory rear end had wider shoes. My question is what is the most common...

I have the 273 low compression engine in my 64 Valiant with push button automatic tranny. If I want to have a little more power and decide to go with a 340 will that bolt up to my tranny and can it take the extra power (assuming the tranny is good to begin with)? I feel the car has no get up and...

Are these available anywhere? Reproductions?

Is the Valiant trunk lid the same for a 64 and 65?

I converted my 64 Valiant from a single master cylinder to a dual. All four wheels are drum as from the factory. When I step on the pedal I have to stand on it to make the car stop. Many have said I need a drum brake proportioning valve or do I need residual pressure valves? I thought many here...

I bought a 64 Valiant and it has an edlebrock 600 CFM 4 barrel carb. I believe it is over carborating this factory stock engine. Should I give up on this set up and go with a 2 barrel intake and carb. It just will not run and idle below 1200 rpm's. Other than idle it runs great.

I need a drivers side vent - fresh air box. My door broke off mine.

Years ago we would of used a shakle extender on the rear end of the leaf spring and added air shocks. That puts stress in the shock mounts and uses the shocks in a way they were not designed. If I want to raise the rear of my car about 2 inches what is the best way? Add leafs?

I want to convert my single cylinder master brake cylinder to a dual. Which brand or who's product (model) will fit (work) the best? I have a 64 Valiant.

I want to convert my 64 Valiant grill to a Barracuda. Need a complete grill.

I've seen where to buy the center dash in new chrome as well as the gear shift selector but where can I purchase the radio trim plastic in new chrome finish?

I may be faced with either rebuilding my 273 in my 64 Valiant or buying a different engine. I want to keep the original factory push button transmission. My question is what is the largest engine that transmission can handle? 273 , 340 or 360 are my choices. I just do not want to go bigger if it...