Search results for query: *

432 low deck. Howards hydraulic flat tappet cam, Crower lifters. MRE 1.6 roller rocker arms and MRE rocker shafts. 8.90 effective length pushrods with 5/32 radius ball/cup. Felpro .039 head gasket #1009. Rocker arm sweep contact on valve stems was approx .055 inch width, contact starting...

Any recommendations for valve spring compressor with engine in car? Comp and Proform offer spring compressors. The Comp handle looks like it may interfere with the fenderwell, power brake booster, etc. Would think the Comp is better quality than the Proform. Search thru this forum did not...

Just bought this gun recently because it is small, easy to conceal carry, is single stack, and my wife can shoot it easily. First thing took it apart, cleaned and lubed per owner handbook included with the gun. Then to the range to break in and test for initial reliability. The FMJ rounds I...

360 engine with oem cast crank, oem front damper, Ross forged pistons, eagle rods, and steel flywheel. Externally balanced including damper and flywheel mods. The new owner of the engine installed a flexplate for auto trany. Can he take the flywheel and flexplate and have them weight matched...

432 "B" engine, Crower hyd street cam with .50 valve lift, Comp single valve springs with 120# seat and under 300# open. Smith Bros ball/cup pushrods with thru the pushrod oiling activating Crane 1.5 ratio iron rocker arms. After approx 600 miles the cup ends of most of the pushrods (not all...

383/432 bored 30 over, honed wth NO torque plates. Can I run moly rings or am I better off with iron rings that will wear into the bores? Trying to not have oil blowby the rings. I assume I cannot torque plate hone it now without leaving the pistons too loose in the bores. thanks

Brother DB2-B790-3 industrial sewing machine. Good used condition. Walking foot, locking reverse stitch, Arrow electric clutch motor 110 volt, table, bobbins, manual, other attachments. Knee operated sewing foot release. Has built in oil sump below the machine. Would need fresh oil and its...

432 engine. 5200 foot elevation. Heat crossover blocked under intake manifold. Mopar OEM style vapor canister in fuel line between mechanical fuel pump and carburetor. Primary jet .107, second jet .104, meter rod 7547 with pink rod springs to go with 14 inches manifold vacuum. If 10-12...

Parts for sale. Free shipping to lower 48 states if you buy at least 3 items. Paypal is ok. PM me on this forum. My zip 59719. Small block bell housing inspection cover off a 1970 Duster. Both bolt holes have good threads $25 Starter dust shield off the same...

Carb part number 1406. Electric choke. I bought this carb new, was used on another project that I no longer have. The carb worked fine with no issues. All the jetting and metering rods are original. The float setting has been checked and set to spec. Throttle linkage hole has been sized...

CERAMIC Dougs Headers D453 for sale. Fit A,B, and E bodies. http://www.summitracing.com/parts/dou-d453 Ceramic coating never polished, so coating is full thickness. Have about 2000 miles on them. Clearance dents near oil filter, passenger side, see the photos. Header collector reducers...

So the pinion seal is leaking and need replaced. Before removing the pinion gear nut, take a center punch and mark the end of the pinion gear and mark the nut right next to where the gear was marked. These are your ‘locators’ for when you reinstall the nut. If your using an...

After the vehicle sat for the winter, I noticed the heater hoses are covered with a sticky shiny coating. It does not wipe off with a dry towel. The radiator hoses do NOT have the gooey coating, only the Gates heater hoses. I thought maybe there was oil in the cooling system after a recent...

Building a 383/432 stroker for street use, probably 6000 rpm max. Have a NIB Crower hyd flat tappet cam. Plan is to break the cam in with the oem valve springs and stamped rocker arms. Then switch to Comp 911 springs and Crane 1.6 iron rocker arms. Checked the rocker ratio with .080 lash...

Home ported the 906 heads. For info as to what worked and what to look out for I used the following websites: Part 1, big block heads http://www.moparmusclemagazine.com/techarticles/5115_cylinder_heads/ Part 2, big block heads...

This Engle Racing cam was produced by the original Jack Engle Cams prior to year 2010. The cam was saved for a project and never used, engine was sold without it. The cam is NEW IN BOX. This Engle K56H cam is for a small block LA 273,318,340,360. Cam is hydraulic flat tappet with faster...

Crower hydraulic flat tappet "340 special" cam for small block mopar. NEW in box. Cam card included. 267/272 seat duration, 210/216 dur at .05 lift, .444/.444 lift, 114 lsa. Specs very close to OEM 340 cam. Will work with higher rocker ratio if desired. Wide lobe separation for smooth idle...

Mopar 10.5 inch Aluminum small block bellhousing casting #2892482. Transmission bearing retainer opening enlarged to accept larger 308 bearing. Bellhousing opening measures 4.805" inside diameter. I used this bellhousing on a E-body, and clutch pivot attach holes are there for A-body also...

New in box Comp Cam 268AH-10 for small block. Includes cam card and Comp lube. Will be double boxed for shipping. 268/276 seat duration, 222/226 at .05, .464/.464 lift, 1800-5800 rpm. Summit info: http://www.summitracing.com/parts/cca-20-309-4/overview/make/dodge Asking $70 OBO including free...

Moroso #25150 lifter valley oil baffle, in very good condition. Will fit all OEM flat tappet small blocks. I had it in a 1974 360, tweeked the pushrod holes a little for perfect alignment. The spring ends rotate and hook under the cylinder heads. It fits great and stays where you put it...

Big Block oil pan #187, matching 3/8 diam pickup tube, and drain plug. This is the preferred oil pan for BB swap into A-body. All parts clean and in good shape, no rust, no damaged threads. Asking $100 OBO including free shipping to lower 48 states. My location: Dillon, MT 59725 The first...

There is some 'R' language. This is my kind of weatherman...accurate and straight to the point. North Dakota Weather Alert! Freeze Your Balls Off_Stay Inside - YouTube

Slowly building a "B" engine 432 stroker. I am doing as much of the work myself as possible. Here is the short block costs: Complete engine, 1969 383 oil pan to intake manifold $250 Stroker crank, Scat forged crank, 3.75 stroke, Flatlander Racing $886 #4-383-3750-6760-2374...

For a bunch of reasons ended up changed the crankshaft main bearings with the crank in the engine, and engine in the truck. Removed one main cap at a time, not loosening them all as some have suggested. Inserted a nail into the crank oil passage, then rotated the crank and the nail easily...

Over the last half dozen years I have slowly put the Challenger back together. I installed a nice 360 V8 engine. The engine runs great. I am getting older than I ever expected to live, and have decided to put a big block in the Chally, so the small block has to go. I could make a youtube video...

These photos are off an original strip kit instruction sheet.

The first person that makes payment owns the carb. Location zip code 59715. SOLD #6322 1973 440 Auto, federal All correct jets and rods: 4098-5125-1966 pri-sec-rod New primary throttle shaft bushings installed I ran this carb on my 360 for 2 years. I tuned it for my 5000 ft elevation, so...

Any of these carbs could have the primary throttle shaft bushings renewed. This is easy to do using thinwall valve guide inserts swaged in place and reamed to fit. These carbs all need a complete cleaning and rebuild kit, not too hard to do really. Brass floats available on Ebay. I have...

Kit #10-114. Fits 850 cfm carbs for 1972 400 CID. The jets can be used on all 1972 and later TQ carbs since they are solid liquid fuel metered. The earlier TQ carbs were air metered. Asking $70 OBO and free shipping in lower 48 states. Location zip 59715 Send me a PM on this forum. I will be...

Edelbrock #61779. Small block Performer RPM magnum style cylinder heads fully assembled. Valve stem to guide clearance was checked and adjusted as required prior to running the heads. These heads have been run about 3000 miles with a mild street cam. ARP 7/16 diameter rocker studs included along...