Search results for query: *

Anyone interested in trading? Looking for a 6 cylinder auto trans hardtop wrangler. The duster has current California registration. Clean title in my name. Very clean body , nice floors, good glass and trim. Has light surface rust only. Has auto trans. I drive it to work 2 to 3 times a week...

Have new master, all new slaves, empty brake lines, everything is dry except for the master which I bench bled and is full of dot 5. Have slave bleed valves open down below. No fluid will come out of the master. Do I need to push my brake pedal down and put a wedge in to keep it down? Even...

Been on the mats website to try to get some detailed info about tech inspection for different classes. They mentioned no leaking fluids and check your brakes and tires and also referenced checking dates on the seat belts. One question I have is does the date codes for the seat belts matter if...

05 ram 5.7 cranks over ok. Had her check fuel pump fuse and relay in fuse box under hood both checked out ok, don't know where to have her check next. Truck has 115,000 miles on it. I'm guessing fuel pump but I'm 150 miles away. I just talked to her again and were trying to reset computer by...

Wanting to adjust valves on 340 with 273 rockers on hydraulic lifters. Have read on other threads to get the cam on the lowest point for selected rocker ( that part is easy enough for me ) then rotate pushrod with fingers while tightening adjuster until pushrod becomes a little stiff to...

Anyone have experience running these shims? Ordered some and have them on the way but wonder if there is any nightmare stories associated with them. Going into 340, stock cam, stock compression, x heads, 273 rockers with the cup and ball pushrods. Will probably never see 4000 rpm just a...

Going round and round trying to trace down the grounding for the front blinkers. I cleaned up the ground to the front lighting harness that is on the front in-between the radiator and battery but that did not work. Tried to trace the wire directly from the plug that connects the to the...

How hard is it to install a reverse manual valve body into a 727? My mechanical skills are decent but I have not been too deep into an auto trans. Also is there any reason at all to keep the kickdown linkage in place or does it get removed?

Just picked up a 340 block that I am told was bored, new cam bearings ready to go but then sat uncovered in a garage for 5 years and now has a light coat of surface rust over entire block, cylinder bores and lifter bores included. Looking for a cure.

Does anyone know where to get the lower radiator hose with the spring. Everything I find has no spring.

Does anybody know of any good way to remove the pin that holds these handles on?

Going to do disk brake swap on to my 70 Dart. Do I use the 70 dart lower ball joint or the 73 and up lower ball joint ? Looked on autozone website and they were different part numbers for each application.

I was wondering which oil we need to use in our torqueflites. I am running both 904's and 727's in street car applications. Would you use a different or special oil in a race car trans or even in a street car with a reverse manual shift valve body.

Got my 70 dart out for a spin and every gear was first gear. Park still works fine but put the car in what should be reverse and it's in first, same with neutral it's all first gear no matter where you move the shifter except that park is working fine. The pointer on the column is working fine...

Need rear valance 70-71 dart or demon I am located in California

Just built a 360 and was trying to prime oiling System but I only get oil to rockershafts when Crank is in one spot. If I rotate the crank I lose the supply of oil to the top end. Different spots for each bank on crank location when it does feed the oil up top. Is this normal or is...

Has anyone tried to use the b&m Flexplate 10236 with a 904 trans? B&m lists this application for the 360 727 combo and lists a different plate For the 904. I am going from a 318 904 to 360-904 and already have the Flexplate from a different project. It Does mate with a 10 inch...