Search results for query: *

how much can you bore out a 360 block? its .030 over now, but has some scratches on a few of the cylinders that I can catch my finger nail on. it appears to be a 1973 block .

Im installing a new cam in my 360 block,I didn't take the motor apart so I need some help.Beside the cam retaining plate is there suppose to be a washer behind the cam drive gear? It seems to me that the cam moves to far forward making the cam lobes not line up on center of the lifters. This is...

magnafuel 500 pump 175.00 holley 1050 angular discharge carb w/adj air bleeds 300.00 mopar bb flex plate 25.00 csr smblk waterpump 150.00 bblk ati harmonic balancer w/bolt 125.00 bblk milodon oilpump and dual pickup & lines plus rebuild kit 175.00 bblk b&m flex plate 75.00 barry grant...

Need 72 dart driver side front windshield verticle chrome molding.

Have a cast iron intake manifold , inside the manifold in the runners there is dark brown coloration, I assume that this is rust because the manifold has been sitting for some time. My question is how to get the surface rust out of the runners? Thanks in advance.

What position do the rocker shaft oil holes for the rocker arms face? Face up or face down?

Mopar mega block 4.505 bore, pn 2468330-m. program main caps ,lifter bores bushed and indexed, deck o-ringed, billet main seal cap. $2800.obo

I am priming my 340 , have 60 psi on gauge but no oil bleeding off the rocker shafts,what am I doing wrong? The passenger side rocker shaft is off the head while priming motor.

need some information on a problem I have, was driving my dart just cruzin along oil pressure was 60 psi , then for some reason it dropped to 20 psi while driving same rpm. Got home did a quick assessment of situation notice very little oil lin price valve cover. Pulled distributor, spun oil...

FBS cylinder heads cnc'ed titanium valves,single intake ,intake spacer ,valve covers ,offset lifters, t&d rockers. Made 949 on hp with nos cam 540cid. $5000 (Price made legible by moderator)

Anyone have experience with eagle or K1 rotating assembly's? Which is better? Pros and cons opinions, need to be able to tolerate about 550 to 600 hp. Much thanks

WTB horn relay for 72 dart. Also need 36 tooth speedo gear for a833 4 speed

Can use some help on how to set pre load on 340 with hydraulic roller cam and roller rockers,

. Trying to put in my 4 speed tranny, but I'm about 5/8 of a inch from bolting up to the bell housing and tranny won't go in any further. I installed a new pilot bushing into the back of the crank. I installed the bushing flush with back of the crank flange. My question is this the right...

I have 72 dart, when I press the horn on the steering wheel the horn does not sound.When I apply 12v to horn On bench they work.My question is there a horn relay somewhere that I am missing. the wire is connected to the steering wheel .

Interior trim piece that goes on the top of the front windshield that covers up where headliner meets the windshield for 72 dart

have a question on how to remove burnt oil from header tubes without removing the coating, any recommendations welcome.

Is there a easier way to change the lower steering column bearing without taking the whole column apart on a 1972 dart?

Does anyone have a source for a service manual for 1972 Dodge Dart to purchase?

Need help with identification of clutch,also is my pressure plate toast? noticed the bluing on the surface thank you for your input

Im redoing some brake line on my dart, my question is the lines from the master cylinder to the proportion valve has loops in them. Can I eliminate the loops and just go straight to the proportion valve to clean up the look?

STRAIGHT strut rods for 1972 dart.

Need help locating lowerControl arm number 10180 and 10179 where to get knew any help would be greatly appreciated

I have a small block 340 came with a ATI balancer, pulley's don't lineup so I need to switch to a stock balancer. my question is are the balancers universal will they fit both cast iron and steel crank style?

need stock harmonic balancer for 340 small block,my ATI is too wide pulleys do not match up.

How do you get the knob off the light switch with out breaking it?

I have a 72 dart, I am looking for a new filler neck and boot that goes in the trunk to seal the filler neck to gas tank. Looked around in usual places on mail order, but cannot seem to find parts. Are these available? any info would be greatly appreciated,

Just looking for a good supplier of hard to find weatherstripping for 72 dart,

On my front plastic grill 3 of the mounting tabs have broken off, is the a way to fix this problem, i.e special glue or other bonding agent? much thanks.

I have the dash out ,gas gauge did not work why I drove the car last year is there anyway I can check the gage to see if it's not broke? much thanks