Search results for query: *

Can anyone tell show me a picture of the rubber truck seal installed ? I am not sure what side gets glued down....I did a search and could not find a picture

1963-1966 A Body Bucket Seat Brackets in good working condition. The one side is missing the wire that goes in-between the brackets. I can ship these at extra cost. $375.

So im getting ready to convert my 66 Dart from Bench seat to buckets, does anyone know if the floor is dimpled for buckets from the factory? Or do I have to basicly make my own holes?

OK...I have grown tired of the search for original bucket seats for my 66 Dart, can anyone recommend some aftermarket seats that will fit ?

I have a good original radiator from a 1966 V8 Dart. Located in Pottstown Pa. Please PM me for more info. $225.

So im putting a Ron Francis wiper switch into the Dart .. I have 4 wires coming off the wiper motor, anyone know how they connect? I have the high speed working but nothing on the slow speed.

So i have no spark when cranking... i did the ground test and it passed..Triple checked all my wiring... all new 6AL ignition box and Blaster 2 coil...Msd pro distributor, new, i turn the key and get the 5 leds on the box...then when cranking i get no leds...any ideas? Im at a loss here...

So i want to use my 66 Dart steering wheel on my Ididit universal column and I cannot find an adapter anywhere, does anyone know what adapter fits this setup?

Im running my Ron Francis wiring system and I have a Tremec 5 speed. The trans has a 2 wire safety switch on the tailshaft, My wiring diagram only shows 1 wire running from the starter relay to the safety switch. What do i do with the other wire? Still waiting on a call back from RF.

How do you measure a V belt size if you dont have the belt? I need 2 v belts fir the power steering and the alt belt on my 5.9

So why did Dodge offset the drivers side Rad support by an inch?

I thinking about modifying my rad.core in the 66 Dart to fit a 26" radiator, I was wondering if anyone else has gone thru this mod.? looking for some advice....

So im shopping for a radiator for the 66 Dart, 408 stroker...I have been cruising the forums here to get info on the best rad and fan combo for my application, has anyone had any experience with these? 62-74 A,B,C,E Body 18x22 Manual Aluminum Performance Radiator | Cold Case Aluminum...

so i installed a Edelbrock Fuel regulator and it has a vacuum line hookup, where is the best place to route that to? Carb?

I am going to buy a bracket, Pulley, and Alt. kit for my 408 from CVF...For the water pump pulley they offer a under drive or high flow option for the water pump pulley. So my question is do i want to slow down the water flow and keep it in the radiator longer or increase the flow? I am running...

I have a complete 66 Dart K frame and front suspension for sale, Let me know what you need..$300.

Im looking for a front motor plate for my 66 Dart small block, does anyone know of a company that makes these?

Looking for a used set of DD7 Headers for small block

So i need some suggestions on a radiator for my 66 Dart build, the engine is a 408 532 HP Street car Im thinking i want to go with an electric fan, so what is the best setup..? 4 core twin fans ?

I have this Y pipe that I had made for my 1966 273 small block Dart. I bolted it up but then changed my plans...$100. plus shipping

So im looking for some mounting location ideas for a remote oil filter in a 66 Dart??

Has anybody used Dougs Headers D454s with the Gerst front suspension? They are made to fit using the Reilly Motorsports Alter-K-Tion front end. The 2 suspension systems are very similar and i need to make a decision on headers, The others im considering are TTI but they are bent for a stock 66...

Will later model Dart bucket seats fit in an 66 Dart?

Finally made it to this stage, I got the bellhousing dialed in and figured out the air gap for the Hydramax bearing so the trans is now mated to the engine!! Ran out of time so next week it should finally be in the car.

The new engine for the Dart is finally here, now the fun really starts!!

does anybody have a picture of a 66 Dart trunk weatherstripping? I have the new stuff but of course it’s not self explanatory..

I am in need of a crank centerline height measurement since I wont have my engine for a while. I need to set the height on my transmission to cut the tunnel out...Thanks...

So I am in need of an A body crossmember for a TKO 5 Speed, is there anybody out there making these for a 66 A body?

Hey does anyone know where I can get a floor jack adapter that fits a 5 speed tranny?

well I got the whole shop all cleaned up and ready for a special delivery coming Tuesday...!!! Stay tuned for pics!