Search results for query: *

Hi there, i have a new mechanical Autometer oil pressure gauge that reads accurate but very slow to react, it's fed by a copper line that isn't kinked but seems to be smaller in diameter than the nylon tube supplied with gauge, i will change the feed line to check if it's the problem but just...

I needed to pinch a part from another of my cars today to get this one going, so tonight i was going to order the part to replace it and to my surprise i think there made of real gold , the price certainly reflected it. I think i will cut and fold one myself. It probably don't even need the...

The other month i had to remove the right hand side extractor to fix my oil lines, i had used Remflex gaskets 6027 , this engine hasn't been fired with them so just torqued up to the 20ft they recommended, anyway getting to the point, the bloody thing separated at #8 and stuck to the extractor...

Hi all, today i got enough parts together to convert my sender to 3/8, from the old 5/16 tube. I had done this around 25 years ago to another car after reading a mopar mag with the write up on it. Not sure if anyone still does this today with all the options available in fuel systems. So...

Hello, I have a small b&m blower manifold that has only a small 1/8npt port on 5&7 runner's, this i will run to a gauge, however i need to run a line to the carb that is boost referenced and also a line to the boost retard on the msd box, these have the larger hose nipple than the gauge, so i...

Can someone school me on 727 slip yokes, I have 3 long yokes and one short, the short is the better condition of the four, the splines seem to be equal length on all four. I'd like to use the short one but it's the odd one out so that tells me the longer is better. Any advice please.

Hi all just starting to put a few mopar related videos up on YouTube, they will most likely be few and far between and just done on my phone. This one today is how to cheaply remove the pin style terminals from the housing with a pop rivet. Thanks.

Hi all, what t/bar boots last longest with the bigger bars, i installed some mopar rubber boots on some 1" bars and they split on the small end within a few years, pain in the *** and they weren't cheap in this part of the world either. Anyone had some luck with other brands?

Who has the best high flow thermostat, i read somewhere on the net too only use milodon but was no reason behind it, anyone done back to back testing on high flow stats.

Hi all, will .002 copper shim work to block the crossover port using 1213 gaskets and extractors.

This is for anyone that has Milodon 30940 pan and the corresponding dipstick 22060 that don't want to run the pan to full oil capacity and find that the dipstick is a bit short, for around a dollar you can fix it without to much drama, you'll need a length of 3/32 or 2.4mm stainless steel tig...

I have looked at my latest small block project and decided to delete the factory bypass hose and run a smaller diameter hose from inlet manifold to radiator it would be through 3/8 npt to 8an fittings and hose, i still run the thermostat but will have all water going through the radiator instead...

Hi all, can anyone tell me the approximate length of the 3/8 unc bolts for alternator, water pump and alt bracket for LA 360. Thanks

Hi all, I'm new to these mini starters, i have two here , yes one to take on long adventures as i don't trust the longevity of these cheap units, my question is about the drain hole in the solenoid side, the one mounted has the hole facing up, and the other has the hole on the bottom side, did...

Hi all, I have made a one or two posts here so thought id introduce myself, Luke aka dodgy, Yes another Aussie, I'm sure you guys have lots of us hiding out hear. I have owned Many Australian Chrysler cars over the years(I'm in my late 40's) from my first car on and only within the last...