Search results for query: *

Does anyone have or know of a cross reference for Mopar hardware? I'm looking for a list of Mopar 6 or 7 digit part numbers converted to common hardware descriptions. Examples: 446363 = 3/8" Type A flat washer 9421589 = 1/4-20 Pan head screw Thanks, Ken

Getting ready to buy carpet, seat upholstery and buns for my ’64 Barracuda. ACC and Legendary. Does any vendor have a sale going on now? Or do you know of an upcoming sale? Thanks, Ken

I am in the process of repairing/rebuilding the wiring harnesses on my ’64 Barracuda. Need help identifying this part. It is part of the body wiring harness (wiring in the trunk) and is located just forward of the jack. It appears to be molded over the wires and is part of the wiring loom. What...

Still doing some planning for rebuilding my engine compartment wiring harness. It seems that the weak spot in the wiring is taking the full current through the bulkhead fitting to the ammeter. I plan on using headlight relays to cut down on some of the current. The wiring “killer” appears to be...

Working on my '64 Barracuda wiring. In checking old threads I have found conflicting information (don't figure) concerning wiring up a dual field alternator, an electronic voltage regulator and an electronic ignition kit. I believe that the attached sketch shows the correct wiring. Could any of...

Rebuilding the dash wiring harnesses on my ’64 Barracuda. Am looking for a part number, description, and source for the female terminals in the printed circuit board female connector (P/N 2258651). The actual female terminals are 5/8” long and fit over 3/32” diameter pins. Also looking for a...

I am considering building (rebuilding) an engine & forward wiring harness for my ’64 Barracuda. Electronic voltage regulator (3438150), Electronic ignition kit (P3690426) and mid ‘70s square back dual field alternator. Questions: Are there any downsides of increasing the wire sizes in the...

This part fell on the ground as I was disassembling the bucket seats on my '64 Barracuda. What is it and where does it go? Any help will be greatly appreciated.

I have a '74 360 and am using a 90* oil filter adapter. I don't believe that I need or can use the oil filter adapter plate. I need a conformation from FABO gurus.

I would like some advice from FABO members. I’m finishing up the final assembly of a ’74 360 which will go into my ’64 Barracuda. Of course, I can’t find the water pump pulley. The original engine had PS and AC, neither of which I am going to use. The existing alternator pulley has 2 grooves...

I would like to give a thumbs up to VintageGlass.com. Needed a windshield for my '64 Barracuda. I wanted non-tinted. Found several other vendors that only had them with a tint or the dark blue strip. Vintage could supply all three styles. Had it quoted and I sent an email ordering it on April 30...

Attached pic is of some engine gaskets that I can not identify. Engine is a '74 360. Gaskets are from a McCord gasket set 95-3038. I don't know if I don't need them for that year or what? Thanks in advance.

Has anyone dealt with Vintageglass.com?

Does anyone have the location of the rear seat hold down brackets for a ’64 Barracuda? Mine were removed when the floor pans were replaced. Thanks in advance.

Looking for a non-tinted windshield for a '64 Barracuda. '63 to '66 Barracuda, Valiant and Dart will work. Ideally can be picked up anywhere between Cleveland and Florida, via I-77, I-95 and I-75.

Trying to finish up the electrics for my ’64 Barracuda. Using a ‘74 360, 0.030 over, 9.0:1, mild cam, Offenhauser dual plane, 650 Holley dual pumper, 833A four speed, Spitfire headers, Mopar P3690426 electronic ignition kit. Street driver. Not a race car. I don’t want to go overboard with exotic...

Need the entire assembly including the pigtail to the wiring harness. Not sure what years/models will work. Will be at the Nats on Saturday (8/13) for pick-up if convenient.

Will need with keys. ’61 through ’65 Valiant, Dart and Barracuda will fit. Not ’66. Please indicate the donor. Will be at the Nats on Saturday (8/13) for pick-up if convenient.

Front bumper stabilizer (Z shaped spacer between the bumper and the body) with hardware. Some ’64, and ’65 Valiant, Dart and Barracuda parts may fit. But not all. Please indicate the donor. Will be at the Nats on Saturday (8/13) for pick-up if convenient.

Some ’62, ’63, ’64, and ’65 Valiant, Dart and Barracuda parts may fit. But not all. Please indicate the donor. Will be at the Nats on Saturday (8/13) for pick-up if convenient.

These are located behind the front tires. Some ’63, ’64, ’65 and ’66 Valiant, Dart and Barracuda parts may fit. But not all. Please indicate the donor. Will be at the Nats on Saturday (8/13) for pick-up if convenient.

Looking for seatbelt bolts for my '64 Barracuda. Front and I am adding rear belts. I believe that I will need C-11 bolts. All (8) connections will be singles. I have been unable to find a source for new bolts. Does anyone here at FABO have a lead for a supplier? Or does anyone out there have (8)...

Looking for seatbelt bolts for my '64 Barracuda. Front and I am adding rear belts. I believe that I will need C-11 bolts. All (8) connections will be singles. I have been unable to find a source for new bolts. Does anyone here at FABO have a lead for a supplier? Or does anyone out there have...

I would like to install (2) rear seatbelts in my ’64 Barracuda. I’m looking for information as to where the anchors should be located. I found an article written in 2003 by Neil Brommell and published on The Early Valiant and Barracuda Club website. Although informative, it did not provide...

I have found two different rear bumper stabilizers for my 1964 Barracuda. The factory parts book and Classic Industries (MA1845) show a thick "T" shaped block of rubber and Detroit Muscle Technologies and Metro (BG101C) show a thin "J" shaped rubber strip. Which one or both are required...

Need some help from you early a body experts. I’m looking for information concerning the installation of the front (headlight) and rear (door jamb) splash shields on a ’64 Barracuda. The rear shields seem to be pretty straight forward but front shields are a mystery to me. How are the front...

Looking for information pertaining to the interior of a ’64 Barracuda. I’m doing a complete interior restoration. Interior was stripped out years ago by the PO. What goes under the carpet in the cargo area? Some threads seem to indicate that on later models the carpet was just glued to the...

I'm in the process of partial replacement of the floor pans. I'm welding up the extra holes that the previous owner put in the floorboards. Lots of drilled holes that don't seem to have a purpose. There are also two small punched slotted holes located under the passenger side bucket seat...

Long time lurker. Figured it was about time that I joined, especially now that I need help. I have a ’64 Barracuda that I need help reassembling. It was taken apart by the previous owner and I have had it in storage for about 30 years. I have lots of questions concerning missing parts and...