Search results for query: *

I'm replacing my outer tie rod ends with Moog ES319R which rockauto lists as the correct part (no L or R indicator so I assumed it was good for both sides. The old one came off easy with a reverse thread (screw in to remove). The new one seems to be the opposite thread. I feel like I'm going...

I know i can get these aftermarket but seeing if anyone has these laying around. 1) One of the upper control arm bolts I removed when replacing the control arm just had a regular washer on it vs the concentric washer. I assume that's no good so looking to see if anyone has 1 washer before I...

So I'm rebuilding the suspension on my 68 dart. It's all apart, new lca bushings in and new Qa1 uppers ready to go. I was reading the install advice on here and realized I forgot to check to strut rod bushings. They are indeed bad. Right now the rods are disconnected from the lca but connected...

Im doing a front end rebuild and am left with the LCA pivot nut which just spins the shaft when trying to remove. I left some tension on the torsion bar but that doesn't seem to help. I can't see anyway to hold the shaft still. Based on the other bushings, this one is probably non existent...

In the process of removing my lower control arm for rebuild, the nut from the pin fell somewhere in the engine compartment and I cant find it. Are these bolts easily replaced or are they a special size? Thanks in advance.

I have a 68 Dart with front drum brakes (4" pattern) which I'd like to keep. I wanted to replace the front A arm bushings and upper and lower ball joints and not sure if if its easier (or even possible) to replace with all new tubular or new a arms, etc. I'd like to get the offset bushing...

I have a 68 Dart which the previous owner replaced the ignition components. New Mopar electronic distributor, new orange box, new coil. it’s been running fine until yesterday. Moved the car out of the garage and wouldn’t restart. Seems to be lacking spark to the plugs. I confirmed spark out...

Hoping for some direction....have a stock 360 with a carter carb. The car has run fine up until today. It starts right up, goes into gear and will run like that all day. Put it in park and it stumbles and dies within 15 seconds. Fires right back up. I can understand if it stalled when you...

i have a 360LA in my 68 dart. The radiator is a new aluminum 19 inch core width, the fan is a 16 inch non clutch, and it’s shrouded. the thermostat is a 185 high flow. At idle the car can climb as High as 230 pr more…I know this is dangerous territory. at cruise it drops tom185 to 190. my...

My secondaries do not open full vertical as a result of the shaft end hitting the choke spring. Any help on how to remedy?

I’m trying to verify the CFM for my current carb which is a carter c-6090. Ideally I’d like more acceleration ….from what I can tell it’s a fairly stock 360 with a performance intake. Anyone know the CFM ? Ty

I took my front wheel off today and the stud fell out the back of the hub. The knurled hole is not holding one stud in and it just spins. Anyone have suggestions beyond replacing the hub?

I can’t believe I’m asking this but I’m getting different answers from reliable sources. Trying to time a 1974 360 and being told #1 is drivers front and also passenger rear. When I google it shows both.

Looking for a 33 tooth long shaft Speedo gear. Currently have.a black 29 tooth that seems to be reading high for my setup. 727 trans if that helps. Thanks. looks like this but would rather have factory https://www.amazon.com/dp/B07L4YBT54/?tag=fabo03-20

I have a 68 Dart with a 360 transplant. The Power steering pump needed replacement so i ordered one. The old one appears to be the press fit pulley and the new one has a threaded end. Other than that they are identical. Will the press pulley fit on the threaded new pump if I add a nut or...

I will be at carslile this Friday only and can bring any parts 1. 64 dart Guage cluster $25 2. 64 dart glovebox, ash tray and side panel $25 3. Early A 4 speed pedals $80 Not pictured...all great shape 273 exhaust manifolds $50 64 dart drip moldings $50 64 dart moldings... Rear window, side...

I consider myself a smart guy but this sway bar install has me stumped. Anyone install an Addco on a k frame with the lip? Only way I can see this working is if I use the angle for the bottom and leave the top ‘floating’ meaning it’s not bolted to the car anywhere. Does this sound right ?

I have bucket seats in my 68 dart. When i look at the seats from the back, It's obvious that the drivers seat is leaning toward the middle (seat back and headrest are tilted). Has anyone dealt with this before and if yes did you just shim up the seat mounts.?

I did the pump it down process on my 68 dart p/s steering pump and it worked awesome for a month at normal local driving. I drove the car 3 hours last weekend and steering at idle was hard when i arrived, almost like manual steering. I checked the fluid level and it was dry. I added fluid and...

I have a 68 dart which had manual brakes - 4 wheel drum. I installed a power brake booster which has an adjustable rod. The car stops very well now but I have issues with the brake pedal not returning or returning very slowly. Can’t see a return spring anywhere. I reused the original master...

Anyone have or know where to get the bucket seat adjuster knobs? Thanks.

I replaced the drivers floor pan and it came with an e-brake cable guide that needs to be spot welded on. Problem is I don’t know where it goes. Is it in line so that the cable is straight or does it pull ithe cable off on an angle? A picture would be awesome but I can’t seem to locate any...

Good condition 64 Dart GT interior door emblems. $35 plus shipping

Replacing a portion of the drivers floor (68 Dart Convertible) and need a few body plugs. Not sure if anyone has a full set and only used a portion of the plugs or if anyone knows where to buy these. Thanks in advance.

I'm trying to remove the rear panels from a 68 dart convertible. I have the 3 screws at the top off, the one round button for the top cover, the window handle off, and there is still something holding it on. Any advice on next steps? I don't want to break anything. Thanks.

I know this topic has many posts but looking for opinions on buy or build. The cost of steel has risen and a 1 1/2 x 3 length of tube to do the job is $70. Wondering if buying is the better option given the fabricating time involved. Thoughts?

Wondering what preformance gains I could expect going to a bigger exhaust. Currently have a 360, 4bbl, with headers going to a 3" collector. The rest of the exhaust is 2"all the way back..true duals. 323 suregrip rear. Would a3 inch or 2.5 do much or leave as is? Thanks

Free 64 Dart parts. Before I get rid of this dart seeng if anyone needs small parts of off it. You pay shipping in a flat rate box from zip 19060. Parts must fit in a flat rate box. Requests should be for parts that take 10 mins or less to remove. If I'm doing something wrong here happy to...

Is this screwed or clipped in? Not sure if the clips are part of the trim or that's what holds it to the car. Thanks

I'm putting new brake pads and hardware on an 8 3/4 rear (year unknown). It has 10" brakes. I ordered shoes which say they fit 65-72. On the shoes I removed, there is a pin for the self adjuster. The new pads have a hole in the same spot. I see self adjuster rebuild kits come with what...