Search results for query: *

I have a 2005 Jeep Grand Cherokee 5.7 hemi, transmission and all computer stuff needed. Engine has 174000 km and runs well. Motor still in jeep so can be heard running. The jeep is not for sale,just what is mentioned above. I will remove the items once I have a deposit paid. I am located in...

Hi there. In the middle of installing my new headliner and one clip is cracked and one broken. Is there anyone near Red Deer that would sell two?? Thanks! Dave

I am looking for one anti rattle bracket for the rear side windows of my 69 dart. I have 3 but one is missing. Thanks!! Dave

I am looking for a driver side fender for my dart. I would like one in very good condition. I am in Alberta, Canada. Thanks! Dave

I have a 69 dart which had power drum brakes. I have upgraded to all disc brakes. I added a power booster from a 75 dart and a mopar alum 1 1/32 master cylinder from dr diff. I can't get fluid from back port of master cylinder. The front will release fluid but not back. Am I missing something...

I have two 1972 Demons for sale. One is a 318 car,needs rear quarters and one small floor patch. The other is a slant six car with required parts to make one out of the two with the exception of the quarters. lt also has a checkered type unholsery which I believe is rare. Also included is a new...

Hi there! Will my stock 69 air conditioning work with an air Gap manifold? E.g Is the mounting provisions provided? Thanks! Dave

I have popped a head gasket on my 360(coolant leaking out side of block only) Can I get away with replacing my .040 thick gaskets with a .028 thick to gain compression without any valvetrain problems? Ratio now is 9.55-1 and have stock non adjustable valve train. Also is it normal for a gasket...

Hi there! Does anyone know of a good shop to have my 904 rebuilt? Thanks! Dave

Ok, Was driving normally when at a stop sign I lost low,drive and reverse.Feels like there is a load on the transmission (like holding brakes on)in first ,reverse and drive. Limped home in second(slipping) Any ideas as to what happened? This is a stock 904 behind a 360 Dave

I have a Holley 3310 carb. there is a provision (port)for brake vacuum,but nothing for the pcv valve. I have my brakes hooked directly to the manifold. Can I hook my pcv line to the carb brake booster port? Or where should it go? Thanks! Dave

I am swapping a 360 into my 69 dart. It had a 273 before. I am using accesories from the 273 on it. I bought a aluminum rad with a passenger side outlet. I bought a waterpump from a 75 dart,but it is too long by 1 1/2" Does anyone know a part number for a shorter one for the passenger side...

My instructions with the msd box say that the ballast resistor is not required. Where do the wires go once its removed. The power goes to the box,but what about the other side? It is a 69 dart with a 2 wire ballast resistor. Thanks! dave

Can I use a 75 dart power brake master cylinder into my 69 dart with power drum drakes? The 75 had discs which i plan on swapping once i have saved enough to do it properly. If this will work, should I use the 69 drum prop. valve or the 75 disc valve. Thanks! Dave

Will an Eddy Air gap intake with holley carb on a 360 fit under the hood on my 69 dart??? It looks like it will be awful close! Thanks! Dave

I have just bought a used edelbrock air gap manifold and it has a few oily thumbprints etc on it. Any ideas on how to clean it up a bit? I was thinking automatic dishwashing detergent and a brush.. Dave

I am doing an engine swap ind need to remove the air conditioning to do so. I will have a shop empty the system,but when I go to recharge the system will the new style freon work with my old system? I understand the old freon is not available anymore. thanks! dave

I have a rebuilt 360 non magnum. It was balanced and has stock balancer to the best of my knowledge. It was in front of a 4 speed and now I want to run an auto. The crank has 7 holes plus a notch.(8 hole?) I want to run a new converter on my stock 904 tranny. What do i need to make this work? Is...

Is there a difference between a 75 904 and 69 904 transmission? Both were from darts. Thanks! Dave

I am looking for a complete 8 3/4 3.91 sure grip rear I would also consider 3.55 I am in Alberta,But would drive a bit for a good one. Thanks! Dave

I have just bought a 360 which was in a 4 speed car. What do I need to hook up to my 904 transmission? I am concerned about an imbalance because the 360 is an external balance,where my 273 was internal. I am planning on replacing the torque converter as well. Thanks! Dave

Hi there! I have just bought a 78 360 from a fellow... It included a separate balanced bottom end with kb190 pistons. On The KB website it says you can't used edelbrock heads with these pistons. Does anyone know why and what heads would work best? I want to make approx 400 horsepower. Will the...

I have a chance to buy a rear end supposedly for an a body with the id number 1820657 on it..There is also a 2 on it and a circled a Any idea what it is? Thanks!! Dave

Hi there! Is this a good year of block for rebuilding and building up? Thanks!! Dave

I need a power steering box for a 69 dart... Mine is leaking and won't pass inspection:cry: Thanks!! Dave

Wanted a 8 3/4" sure grip rear end. prefer 3.55 or 3.91 ratio I am in alberta ,canada Thanks!! Dave

I have a 1969 dart with a 273 engine It has a 4 barrel carb mechanical secondaries. The secondaries don't seem to open. Was the original manifold a 2 barrel? With a edelbrock air gap for a 318-340 fit? I will eventually replace the engine with a 340 and want to be able to reuse the manifold if...

Hi there! I have new quarters bought,but my wheelwells are rusted too.. There are no aftermarket parts for these that I know of.... Does anyone know what I could use instead? Thanks!! Dave

Can anyone tell me from the casting what yr comp ratio this is?? Thanks!! Dave

I have a 1969 dart with 318 4 speed... Want to put in a 340 which was from an auto car... What do I need to change over?? Thanks!! Dave