Search results for query: *

4406FASTBACK Looking to buy the passenger side or complete taillight section from a 1973/74 Duster. The car was hit on passenger side and I need the taillight area to where it folds around for bumper clearance(about 6"-8" up quarter panel. I have 318 2bbl engine & trans from a dodge truck, new...

New GOLD MEMBER....started out as one more rust bucket.after alot of work,and alot of work and and alot of money. After 9 years I finally am driving the 1968 440 Six Pack Barracuda Auto trans,8 3/4 355 posi.,disc brakes up front

would go with the 73 k-member, It will give you the big ball joints,you can use the big tie rod sleeves and tie rods.lower center link will gve you more clearance at oil pan,the idler arm is alot cheaper than one for a 67. Clean it up weld the seams up good and move you motor mounts then go for...

I have for sale a NEW PAIR of AAR Quality Fiberglass fenders these are the heaver version that are finished inside and are built to use on street cars.I paid $295.00 each plus freight and have $725.00 in the pair .I wil sell for $375.00 for the NEW PAIR,must be picked up in six mile SC.This is a...

EASTWOODS.COM has a really TUFF CERAMIC SPRAY CAN paint. GOOD STUFF!

Alternator is fine,as is battery and other parts.Part that is really HOT is the New resistor that came with the Mopar electronic Distribitor kit,it will burn ya,directions says it may smoke for a few mins.,but it stays hot.the coil is HOT to touch.I eliminated the Voltage Regulator and added the...

Please HELP-This is a six cylinder car/wiring harness- First I made upgrades to my 68 Barracuda 440 six pack put NEW Mopar electronic distribitor kit in and the NEW ballast resistor & Accel super stock coil is staying VERY HOT.I have a one wire 60 amp Denso alternator wired with sense wire going...

hey guys don't wanna hi-jack a post ,in Six Mile,SC and I need a good MOPAR MAN to fine tune my motor & carbs.,Have just gotten my 68 FASTBACK 440+6 running and need help with timming and/or carbs Runs good in shop get outside in drive and punch a bit and it detonates bad..I am disabled and...

68 dash pads are unique to the Barracuda's with the upper & lower set,the upper pad sits over the lower pads edge. I have run into this problem right now myself. Have a SUPER NICE 66/67 pad that I can't use.Anybody need a pad dated Dec.27 1966? Has any one tried the repops P.G. Classic sells?

Man I like the look with the SS springs,have 15 X 10 and NO cutting or NOT tubbed.I can't wait to drop the hammer on 68 Fastback,It's comming along,will add a few picts. later .Now have to figure whate shocks,KYB don't look like they have enough travel ....What do you Think..Man not trying to...

New guy to site,Is the Super Stock 003 meant to be used on drivers side and 002 pass side ? Just wana be sure. Thanks

THANKS to All for Welcoming me here.Many Nice cars too! Mopar to YA All !

Nice ride Thanks for the welcome.Terry

NICE BARRACUDA Thanks for the welcome.Terry

440source did have them.good luck

I have been looking every where for the mounting clips that slide inside the 1/4 glass trim & use a screw to mount the stainless steel molding to the body. The correct name is 1/4 glass SIDE SILL OUTSIDE MOULDING and it came as a replacement parts package with attaching hardware,per my parts...

Hello to all From Six Mile,S.C. I have been checking out this site for few weeks now,and Loving ever minute of it. I have a 1968 Barracuda Fastback,work in progress..Getting ready to paint this spring and put a 440hp with six pack set-up,8 3/4 rearend 355 gear. Can't wait!