Search results for query: *

Looking for some guidance and suggestions, My heads have been cleaned up, machine shop says someone has installed valve seats and many are 25 - 60 thousands too deep which I can remember when that was done in the 80's. Scary parts is recommended replacement with oversize seat inserts with risk...

Asking for help from the mopar gods once again, I am having trouble finding info on my 2-speed wiper motor and wiper/washer switch. I have a 2speed wiper , has 3 wires on firewall plug, looks like this: Done my searches, have 67 and 67 fsm for reference but passion4mopars has a...

Up for sale is Kelsey Hays 4-piston brake setup. Fits 67-72 A-bodies and is small bolt pattern. You can use Mustang Rotors if you want to go large bolt pattern. (use search function) I can ship spindles, calipers, backing plates. Still assembled but will separate. Shipping from 98584...

Adjustable, brand new never installed, comes with Large ball joints installed and upgraded to urethane bushed ends and ball joint spanner wrench. Would not work with 18"wheels but would be fine for 17" and under. Shipping from 98584 $250 plus 20.00 shipping to continental us. PAY-PAL ACCEPTED

273 with comp cams 20-233-4 thru 340 hp manifolds and accurate exhaust: Idle quality can be observed the first 3- 4 seconds then I got carried away. What a feeling! Be patient, big file...

Cant seem to get mine to look right, can someone post a pic of the correct installaiton?

Cant get hood to align / fit so I took out the hood bumpers and hood fits. So I compare the original rubber bumpers to what I got: Original on the left. Now on the hunt for correct bumpers so if anybody knows please share.

Fired it up last night for the first time, ran it 20 minutes at 2500 for the cam break in. Had an issue with the power steering pump I rebuilt and have to pull it out to see what I f*** up. I still have to install the front bumper and get an alignment, grease some zirc fittings and install the...

Must be old / tired / zzzz..... FYI My car has the 73-76 K-member / disc brake / Big upper ball joints. The two I have trouble figuring out is 1. The upper caliper bracket to the (knuckle) spindle torque. 2. The lower ball joint bolt/nut to (knuckle) spindle torque. upper ball joint...

It all fits, 18x8 +44 offset 2013 Mustang Wheels and 235/50/18 tires. It is a B-body rear end FYI. 73-76 K - Frame. Had to turn the rotor snout all the way to the mount surface, maybe .040 Going to go with 235/40/18 on the front and leave the rear the same size and ordering new tires for...

For those of you have have a TRW pump and have trouble making or finding a replacement pressure hose, I just found the answer! You only have to change the fitting that goes into the steering gear to 5/16" female sae, took one from a donor steering gear...

I believe 66-67 came with TRW pumps Does not have to be perfect, just need one for template. Looks like this:

Trying to find best spot for voltage regulator, coil and Ignition module. Its on a 67 Barracuda and I do not have the motor in so coil mounting may be an issue. Here are some pics, no holes drilled yet so I welcome advice and opinions and pics of yours if you got em.

HEI style 4 pin Module. Brand new and never installed. From DUI: For a crisper, smoother running engine, replace your stock HEI module with the Dyna-Module. The Dyna-Module has more electronic dwell in it to provide more coil saturation time. The additional saturation time allows the coil...

Brand new, never installed. Pertronix Part Number 44011 Black Compatible with Ignitor II and III systems Dishes up to 45,000 volts of heart-pounding electricity Ultra-low 0.32 Ohms of primary resistance for maximum flow Recharges up to 70% faster than other coils for maximum spark...

Used for mock up only. Could not get pulleys lined up on cast iron water pump. My loss your gain. Install a Denso 60 amp alternator onto any late model small block LA or Magnum Mopar engine. Works only with passenger side inlet water pumps. Uses the Denso 210-0106 alternator. The Denso...

I can't believe I am missing something! Probably get some washers but it looks like a spacer is needed: I checked the old water pump, its the same. Maybe the bolt does not capture the bracket? Has 2 other mount holes.

What is correct paint for an aluminum bellhousing inspection cover and starter shield? I am leaving the bellhousing natural aluminum. Not original to my 67 Barracuda so unclear to what was done. Opinions please.

On an aluminum bell housing are the inspection cover and starter shield painted engine color or black? or ??

To start it is a 67 Barracuda, 273. Completely re-wired the car and have bypassed the amp meter and installed a volt meter in its place. I have read the mad electrical tech docs on volt sensing. I purchased a Bosch AL504x (squareback) and ordered a 70's style voltage regulator. I read the...

I thought it was for attaching fuel line from pump to carb but may be on rear of bell housing for reverse light wires. What do you guys think?

I have a really nice drivers side headlamp bezel, part#2898143 no cracks, screw holes are perfect, another one that is missing a tab next to headlamp and has one small scratch, screw holes are perfect. Asking 75 and 60 respectively. Accept pay-pal and $11.00 flat rate shipping from 98584...

Can some one post pics showing mounting / attaching points on 2-strap gas tanks? Did not realize that 1 strap on 67 interferes with exhaust / tail pipes. Thanks in advance.

What is the correct valve cover bolts? Mine are chrome plated captured washer bolt and not in good shape so I am not sure if they were original. What is correct?

So easy a cave man could do it. Dip it slow and pull it out slow! and before: Shameless bragging! Can't help it, motor is getting close to firing up.

How much room under the hood? Thinking about adding a 1" spacer. The original air cleaner was tall, like 4" so I am hoping I can add a spacer. Any body know?

Up for sale is a reconditioned set 273 Banana Groove shafts, end plugs removed, tanked and new plugs installed, rocker face resurfaced all hardware including 16 pushrods Looking for $150 plus the ride from 98584

Up for sale is an original 67 9 1/2" Flywheel. Resurfaced and ready to go, pressure plate looks good, and disc looks good also, it is a 10" disc and has the much heavier springs than you see with replacement discs.. $200 plus the ride from 98584 I also have the original bell housing...

Can someone explain why / why not use the pertronix III coil, it is supposed to work with HEI type ignition, Its been said over and over again to use E-core when converting to HEI.

73-76 Anti Sway Bar Another good used anti-sway bar. Has original end links, needs bushings on sway bar and missing brackets to K-frame. Easy bracket to duplicate. Mounts to lower control arm with mount tabs. $90 plus the ride from 98584 Pay-Pal accepted.