Search results for query: *

Just noticed today that my fresh air box door when I opened it in the driveway was full of water?? The carpet on the floor was drenched. I think the stupid sponge rubber donut I bought which seals it around the lower cowel pan is leaking. I ran some water in the outside cowl louvers and sure...

Does anyone here know the size and type of screw that goes into the rear of the housing and into the plastic lens of my Demon. I seem to have forgot them. My rear lights are leaking water into the trunk. There are 6 of them on each light and I do not want to use the wrong size and break the...

BTT

Why can't I get the chrome interior threaded escution to tighten. The mirror has a tin nut which gets threaded on first. Then the cable end gets inserted in the door hole from within and the chrome nut threads on to the mirror adjuster knob but it hits the tin nut and won't pull tight to the...

Thank You. Never would have looked there

Thanks. I will look for the hole in that area.

OK, I searched and found my correct bracket as shown in the photo. It also has the small bolt that goes through the sheetmetal and into the captured nut on that bracket. Can anybody here tell me or show me a picture of where that bolt goes through the door for the proper location of that...

Great. My other issue is this. My stripe kit for the rear has that small panel which drops down to connect the upper stripe to the lower stripe which is where I am assuming I suppose to place the Demon name with the little devil art. Now, that drop down black panel is closer to the right...

OK. Got it. But here is my concern. The Demon name on the 72 was placed on top of the black vinyl tab which allows it to sit completely on top of the underneath black stripe. But the 340 spans both the upper and lower stripes as well as the center section which is directly on the painted...

All the ads say 71-72 demon. But I understand that there is an actual difference between the two years regarding the rear tailpanel stripes and emblem. Does anyone here have a picture or an explanation of what the difference is and what is the correct for 72 340 demon?

Got the damn thing installed in my demon. two issues. Remote won't tighten in the door. I installed the backup tin nut and when I tighten the chrome flange nut it only goes so far and then is very loose or sloppy on the thickness of the sheetmetal?? Second issue is the cable routing is...

I have a can of DDL9423 low gloss Black. Is this the best match for my 72 Demon scoop and rear wing?? Does this paint need to have a clearcoat?? It is Duracryl Acrylic Laquer... I also have a can of organisol black,, but I would rather have no texture if that is what is correct?? How did...

Thanks

Am I thinking that one slot firmer is pulling the rod toward the tail lights? My car only has one rod. I think some folks on here seem to have 2 rods on early abody cars?

I installed a wing on my trunk and I find the trunk wants to drop down way too easy. There are 4 slotted holes for the torsion bar adjustment and mine is in the second hole from the front of the car? I am thinking with the wing I need to pull that torsion bar back to the rear of the car but...

Yes, I did find a cylinder in my scrap stuff with the nut on the back.. It fit right in the hole and fits fine??? Why this 72 Car is now sporting the larger lock cylinder with the nut on the back is anybody's guess. I am thinking somebody ordered a cylinder back in time and mistakenly got...

Just looked at a 73 cylinder online and it appears to no longer have that ushaped clip to secure it in the trunk. But it has a rather large threaded not that tightens on the inside of the trunk. Although most places are not in stock, I suppose I should try and find one of those and try it in...

Here are a couple shots. Looking close, it almost looks like somebody punched the old cylinder through? Sucks cause the car is all painted.

Stand By

No. Looks original but the hole appears rather deep when I insert the cylinder. I was thinking the same thing? Wrong cylinder?? Is the face of the cylinder suppose to be pushed in about 3/16"?? Anybody got a picture??

Car was missing trunk cylinder when I got the car. I wonder if somebody took a hammer and punched the cylinder through because they had no key?? The cylinder just fits through the hole so the locking clip will not hold it. Problem is I just painted the car? I wonder if I put a socket in...

Yup, But it goes right through the hole?? I wonder if year one gave me the correct cylinder??

Just got a new trunk lock for my car. When I tried to install it the cylinder just goes right through the hole in the panel?? Did these trunk locks have some kind of small escution under the lip of the cylinder to make it a tad bigger?? The hole does not look like it was messed up??

Anybody got one of these at a fair price that was a good working part? I see Year One says theirs are Factory Direct left side only? AMD says they are out of stock. Mine has elongated pin holes which is making the door very sloppy and hard to adjust. I can bush the upper one, but lower just...

I have a stock fuel tank with the filler tube coming out the quarter panel. I was looking for an idea to still use it, but keep the cap smooth to the sheetmetal somehow?

I knew it. Ok maybe I should say how to eliminate the gas cap so it does not protrude out beyond the car. I already welded the side markers but I am now looking at that gas cap. By the way, I could use a nice meat slicer toooo

anybody post pictures of how to shave the gas cap on my demon so it looks smooth???

looking for the correct clips and screws to install my top to quarter panel at the sail panel trim pieces? How many? Is one of them a screw and nut behind? What about these stud screws I hear about but have never seen? Plastic clips under screws? How many?

Hello, I am getting ready to do the exterior paint. I got rid of the side marker lights as I wanted a cleaner look on the sides. But I keep looking at the spin off gas cap protruding out the rear quarter. I am looking at gas caps for 2014-2015 dodge challengers which are a flip top and they...

Hey thanks. Looking closely it does appear mopar had some sort of custom made drop in mask and then sprayed as I can see the slight overspray even when they did the job. I think I will need a steadier hand and maybe a finer brush. And as I guess I have shown. Being a 100% disabled vietnam...