8-3/4 w/Yukon axles, fuel cell, leaf springs, aluminum radiator, Weld wheels, MORE!

-
Status
Not open for further replies.
clinteg

clinteg

Well-Known Member
Joined
May 17, 2007
Messages
2,495
Reaction score
922
Location
KS
Rating - 100%
2   0   0
Contact seller
These are some parts that have been taken off my car or were left over.

A-Body 8-3/4 rear with Yukon axles and green bearings with approximately 300 miles. Axle housing has been beefed up with straps welded to the spring perch areas - $600 OBO.

I have brand new spring perches in the box if wanted.

15" Weld wheels with LOW mileage Mickey Thompson 235/50/15 street slicks - $400 (tires alone are $400 new)

(SOLD) Race lug nuts (set of 10) - $20

Landrum rear leaf springs - $180

Leaftspring pinion angle shims - $20

Northern aluminum radiator - $130

(SALE PENDING) 12 Gallon fuel cell - $50

(SALE PENDING) Fuel cell mounting straps - buy the fuel cell and I'll throw them in

Holley fuel pressure regulator - $20

Carter fuel pump (not sure this is working properly or not. would not keep up with holley 950HP) - $30

AFCO heavy duty leaf spring sliders - $100

(SALE PENDING) Rear shock plates - $50

741 center section (lincoln locker needs cleaned up. turns easy) 2.7X gears - $100

Jegs Sport Lite 15X8 Wheel - $50

90 Degree AN fittings (push lock) - $5 each

3/8" NPT to -8AN adapter - make offer

Brass push lock fittings - make offer

Aeroquip 3/8" NPT plugs (1 is spray painted black.) - make offer

(SALE PENDING) Fuel filter (unknown brand w/stainless filter) - $30

001.jpg


002.jpg


007.jpg


008.jpg


009.jpg


010.jpg


011.jpg


012.jpg


013.jpg


014.jpg


016.jpg


019.jpg


020.jpg


021.jpg


022.jpg


026.jpg


027.jpg


028.jpg


029.jpg


030.jpg


031.jpg


032.jpg


033.jpg


034.jpg


035.jpg


036.jpg


037.jpg


038.jpg


039.jpg


043.jpg


044.jpg
 
What is the diameter and length of the fuel filter and what size inlet/outlet fittings does it have? Also interested in the shock plates.
 
interested in separating the axle's from the housing? i have interest in the axle's alone.
 
74DartSwinger360 said:
What would you want for them shipped to 33594?
Click to expand...

PM sent

fishy68 said:
What is the diameter and length of the fuel filter and what size inlet/outlet fittings does it have? Also interested in the shock plates.
Click to expand...

I will get the measurements when I get home later. It was set up on a -8 fuel line with the brass push lock fittings.

78kitcar said:
interested in separating the axle's from the housing? i have interest in the axle's alone.
Click to expand...

If I do not get the entire rear sold, I may consider it. But not interested in separating the axles at the moment.


All other inquiries replied.

Clint
 
If you can find me someone that wil buy my bike, I'd take that whole rearend off your hands.
 
65_valiant said:
If you can find me someone that wil buy my bike, I'd take that whole rearend off your hands.
Click to expand...

Heck I would be interested if the wife wasn't so against them. I had to sell mine. :protest:


Sedanman said:
Is the carter pump for BB or SB? Do you have the fuel line fittings? 3/8?
Click to expand...

Pump came off my small block 340/416. All the fittings shown are what came off of it. And yes I believe it has 3/8" threads. The blue fitting is 3/8" to -8AN.
 
The following items have been sold.

Lug nuts
12 Gallon fuel cell
Fuel cell mounting straps
Rear shock plates
Fuel filter
Spring perches
 
SlimPikins said:
What is the width of the rims, and how much back spacing?
Click to expand...

I BELIEVE they are 15X8 with 4.5" backspacing from what I can tell. I have never had the tires off so the wheel width I'm guessing on.


All other questions PM'd. Sorry for the late replies.
 
Status
Not open for further replies.
-

Back
Top