Gauge pin question

[TheGrateRonzini]

Ok, 67 Rallye dash, the three pins above the speedo on the printed circuit, anyone know what order they go in? My plastic connector is gone and I have three bare females (giggity) Does it matter which they go to? They each only power a dash bulb… right?

 

[Murray]

See the FSM.

 

[Dana67Dart]

Ok, 67 Rallye dash, the three pins above the speedo on the printed circuit, anyone know what order they go in? My plastic connector is gone and I have three bare females (giggity) Does it matter which they go to? They each only power a dash bulb… right

You MUST get a wiring diagram and fully understand what the wires do.

Otherwise you could hook a ground to a live terminal and fry the cluster and your under dash wiring.


Red pin goes to the drivers side turn signal
Yellow goes to 2 dash illumination bulbs
Green goes to the oil or brake warning light

 

[Dana67Dart]

If anyone has this terminal loose and will loan it to me I'll reverse engineer it.

I have the round terminal REed I did not know about the rectangular one.

PM me if you can help

 

[TheGrateRonzini]

Blinkers. Red orange and lt grn. Orange for sure in the middle. I think Lt Grn is low and away from the other two. From what fsm says. I think red is left green right. Wasn’t sure if anyone knew off hand. I also have a second 90* stud connector coming off the fusebox like the one the voltage limiter capacitor. I guess Ill have to find out what that is doing. There is a butt connector mid wire, so I don’t know if it’s original. Could be a ground,

 

[TheGrateRonzini]

Car has battery disco, I pulled the cluster to fix pins and one of the bezels was loose. I put shrink tube on the bare connectors for the time being to avoid contact.

If anyone has this terminal loose and will loan it to me I'll reverse engineer it.

I have the round terminal REed I did not know about the rectangular one.

PM me if you can help

View attachment 1716444192

I probably have that piece at the farm on or from another car. If so, I’d be willing to de-pin the other harness and send her for a trip. Probably going out there tomorrow. Unless someone gets ya one first

 

[Dana67Dart]

At this point some dimensions ( length, width, depth, terminal spacing. ) i have all the terminal internal info from the round connector

some good clear close up photos

it looks very much like the 2 terminals on the Dart standard cluster

 

[Dana67Dart]

There is a butt connector mid wire, so I don’t know if it’s original. Could be a ground,

DO NOT ASSUME ANYTHING.

Most oem wiring will look like the other connectors so if it looks out of place it probably is not OEM

post a photo

 

[Dana67Dart]

Almost ready for prime time
Prob 2 - 3 weeks to get real samples!

 

[TheGrateRonzini]

Brake switch? Ha

 

[Mattax]

The '67 Barracuda instrument panel is in the '67 Barracuda Supplement.


This should be a direct link:
http://www.mymopar.com/downloads/servicemanuals/1967_Plymouth_Service_Manual_Supplement.zip
if not, its on this page Service Manuals – MyMopar

There's also pdf of the shop manual diagram by @1969383S in this post.
Make sure you get the '67. There are changes each year.

Diagram wire codes covered here

This assembly drawing may be helpful

Wiring Issue Headlamp not working Continued...

So, I tested to make sure I had power going into Z. It looks like Y is the hot feed to headlamp and X is like a return. I have power on Z but no power coming out of Y. Does the power from the battery go directly to the bulkhead connector and then come out of Y to feed the headlamp or does it...

www.forabodiesonly.com

 

[Mattax]

I think your looking at instrument panel circuit board on the driver's left.
Here's the connector on my '67

Rally dash redo

I popped my Door switches in and then connected the wiring from behind, tough but long pliers help, did not consider holding the button in! They are the 2 contact versions. The parking brake was too easy, adjust and plug in. I don't know the cutoff dates, but it makes sense that the two and...

www.forabodiesonly.com

 

[Dana67Dart]

I have a fully functional prototype of the flat connector, I'll send off a parts order in a week.

 

[TheGrateRonzini]

Welp, I guess I’m a Dodo. I looked at these several times. Couldn’t figure it out. Got my lazy *** out to the garage, 3rd fuse in line, ACC, funky stud connector… I’m looking at the cigar lighter power. Thanks everyone for the help
Dana67, let me know when you have some connectors!

 

[matthon]

I bought a colored laminated 'placemat' diagram years ago.
Very helpful and stays clean.

It's for a 67 however the wiper piece is incorrect for 67 but correct for 68.

 

[Dana67Dart]

Dana67, let me know when you have some connectors

I have an order in now , pm me So i remember