Yep. Our service line was leaking out by the shut off valve. (curb stop)
A tractor and backhoe to dig it up. It was 6' down. $1800 later.
Stop in for a cup of coffee
- Thread starter toolmanmike
- Start date
-
A tractor and backhoe to dig it up. It was 6' down. $1800 later.
Screw that. Lol
I would do what Keefer is doing. 6ft hole in the ground.
I've done plenty.
Unconventional
Well-Known Member
shittyslant6
Well-Known Member
Good Morning! 
I'm going to spend the day messing with my accelerator pump and trying to get a die set big enough to cut new threads on my steering shaft.
I'm going to spend the day messing with my accelerator pump and trying to get a die set big enough to cut new threads on my steering shaft.
zkx14
Duster De-ruster
Sometimes it really sucks to be right.Yep! Yep! That thar am a hole in the ground.
Cant see it too good in pic, but there is a little stream of water off the top of small tube shooting out to the right. Mae is heading over to Home Depot in a moment for repair parts. I’m gonna chisel the old stuff loose in the block.
zkx14
Duster De-ruster
haven't decided how I will backfill this yet. Maybe a couple bags of gravel an a paver or something over it. I can figure that out after the leak is resolved. Pretty sure the original backfill dragging it down is what killed it. The twist to line going to the pump ain't good, but does not look like it actually caused any of the problem. Should be able to fix both problems. Guess I won't be making it to that car show thoughView attachment 1715745289 How many thousand cubic yards of concrete did I make to backfill all the piping of various uses at SLC 6? Dig that up with a shovel. I dares ya!
Unconventional
Well-Known Member
haven't decided how I will backfill this yet. Maybe a couple bags of gravel an a paver or something over it. I can figure that out after the leak is resolved. Pretty sure the original backfill dragging it down is what killed it. The twist to line going to the pump ain't good, but does not look like it actually caused any of the problem. Should be able to fix both problems. Guess I won't be making it to that car show though
Sand without rock is the preferred material on govt spec jobs I worked. 6" above and below. Reglar ole dirt above that should be fine.
Unconventional
Well-Known Member
zkx14
Duster De-ruster
Got it busted free. Big line is dimpled on bottom, but i think I will just put the small one back together and see if it holds. Wife called an told me she had a choice between 2 ft and 100 ft. So I’m buying a whole roll of the 1” to avoid a splice in the wall.
They have same lengths available in the 1-1/4. So if I need to do that one I’m buying another roll.
Stainless couplings and all stainless clamps i hope...Got it busted free. Big line is dimpled on bottom, but i think I will just put the small one back together and see if it holds. Wife called an told me she had a choice between 2 ft and 100 ft. So I’m buying a whole roll of the 1” to avoid a splice in the wall.
View attachment 1715745328
Got fuel lines replaced. What a ***** of a job. Then they are labelled wrong, pressure and vapour. So no start. Flipped lines at tank and away it went.
3 hours. Chevelle next!
3 hours. Chevelle next!
zkx14
Duster De-ruster
Plastic coupling. Stainless clamps. No way I'm getting stainless couplings around here today. Would have to order them.
We got the beer brats cased then she started on the next batch this one with pork shoulder roast. Jalapeno and cheddar.
Fertilizer, propane... all gone.View attachment 1715745289 How many thousand cubic yards of concrete did I make to backfill all the piping of various uses at SLC 6? Dig that up with a shovel. I dares ya!
Shovel out the remains.
Been waiting almost 45 minutes for my telephone Dr’s appointment. Im waiting until 2:00 then im getting back to work.
zkx14
Duster De-ruster
Water lines are back together. Primed the pump and it kicked right in. Think I've had enough for today. Gonna put a few things away and get cleaned up. Probably go get some sand and mortar mix - hopefully get it closed up in the morning.
I could easily check, if I had an engine in my car... Am going to buy a shroud and a fan in Carlisle ...
Last edited:
I got two off a 67 Barracuda that I got last fall in the parts lot I bought. Maybe it's what your looking for??
Yep. I think 18 inch might be right....are they for a clutch type or direct bolt on?
-
Similar threads
