Search results for query: *

when you have the hood black and the rest of the car....I don't know...Yellow or orange or green, what ever, Is the proper color on the hood flat black, semi gloss black or gloss black? Do you spray anything over the flat black base coat?

On my 70 duster, I had to remove the door panel, then I used a mirror to see the screw, then reached up with some needle nose pliers(was a little akward putting my whole arm into the door) and unscrewed the nut until I could turn it with my fingers. I believe the window was rolled all the way...

Thanks guys, I'll try those ideas. The old wire brush on a drill wasn't working very well at all. I don't have to worry about the headliner or anything because everything except the suspention has been removed. 8)

Hey guys, I took the windshield and back glass out of my duster and now I have this black leftover "glue" type crap stuck to the metal. What is the best way to get that stuff off?

Ya, I sure hope so. I plan on going, anyway.

Are you supposed to spray a rust inhibitor like OSPHO on the bare metal before you spray the epoxy primer or is that just an option and not really necessary?

How do you get this damn thing off? I unscrewed the one screw that is visible just by looking at it but it seems like it's being held onto the door by another screw or bolt under the base that I cant figure out how to get to. What's the trick? Thanks for your help guys.

Thanks for your help guys I think I'll just keep scrounging for that mig welder.

Hey guys, I got a welder from my grandfather a couple of weeks ago. When I picked it up, I found that it was an arc welder. Question #1: Will this work as well as a mig welder for bodywork? It has the 220 or 240 volt tri-slotted plug like an old clothes dryer but my home doesnt have...

thanks guys

was just sitting here reading the posts and this question just popped in my head. when i finally get to put the side stripes and other decals onto my 70 duster, lets say i screw up the alignment on one of the side stripes but i dont notice it until it has already dried and set. is there any...

hey guys, when you are pulling out dents, instead of drilling a hole into the sheet metal and using a pull hammer to get the dent out, there is a "spot welding gun" that attaches a "pin" to the dent and then you use a slide hammer to attach to the pin and pull the dent out. what is this "spot...

were the holes circled in red already there from the factory? I'm going to put the same scoops on my 70 duster, but none of the holes are there. Guess I'll just have to guestimate the best I can from looking at yours.

About How Much Paint Does It Take To Paint A Whole Car? Engine Compartment And Trunk Included.

Thanks guys

Hey guys, I went to a mopar only restoration shop here in San Antonio to see if they could cut off the pass. quarter panel and weld on a new one for me, and the guy said they would cut off the old one and weld on the new one and then grind it, sand it and primer it ready for paint for $750 +...

it looks pretty good. my step father put that color on his dart a couple of years ago, and it came out looking real nice.

hello everyone, awhile back, I saw a Duster in a video that had one of those tornado/duster 340 decals on the rear of the car in between the taillights; except instead of the 340, it said duster 360. does anyone know where I can find one of these decals? I already checked Phoenix Graphics...

ok, i went by the measurements here, and the scoops were waaaay off. they were way to far towards the windshield. are there a-body scoops and c-body scoops? maybe i got the wrong ones? are you sure it's 23 3/4" thanks for your help

yup those are them, thanks for trying anyway. any one out there have a duster with these hood scoops on it? would anyone with these hood scoops measure the distance from the edge of the hood closest to the windshield to the edge of the scoop. and then measure from the side of the hood to the...

it's a 70 duster but i'm putting the twin-but-seperate hoodscoops on it. i think the scoops were most common on a dart gt or a coronet superbee. :banghead:

HEY GUYS, I'M TRYING TO ATTACH THE HOODSCOOPS TO MY HOOD BUT THE HOOD WASNT MADE FOR THE HOODSCOOP OPTION. THAT MEANS THERE ARE NO HOLES PREDRILLED NOR ARE THER ANY SORT OF MARKINGS THAT WOULD TELL YOU WHERE TO DRILL THE HOLES TO MOUNT THE SCOOPS. THE SCOOPS LOOK LIKE THE ONES IN MY PICTURE...

hello everyone, i took the front fenders off of my 70 duster and found out that there are rust holes in the "long tab" of the fender. that part on the inside of the engine bay where the bolts connect the fender to the engine bay. is there a way to fix these rust holes? do i have to find...

Does Anyone Know What The Installation Measurements Are For The Dual Hood Scoops On A Duster (like The Ones On My Avatar)? Or Does Anyone Know Where I Can Get A Diagram Of This? Any Help Is Appreciated. Thanks

Hi, Does Anyone Happen To Have Or Know What The Measurements Are In Order To Position The Go-wing On A 70 Duster?