Search results for query: *

Good Day, i am looking for someone in the Tacoma-Seattle (Graham) Washington area that can set eyes on (inspect) a MOPAR for me and relay the gathered information. i am researching to see what works out better and this is one option. PM me for more information.

hey guys its been a while - 1968 plymouth barracuda notchback 440 RB (1973 charger) all stock 727 trans. looking for someone to build it - i'll pull it out with trans and just need it build - been trying to find a shop aroun dmy location but no luck really. i can do it myslelf but do not have...

Hey guys, looking to put some money into the shark- 1968 Plymouth barracuda notch with a stock 1973 Dodge Charger 440 RB. What is the best cam to install on a completely stock stock 440 RB. Looking for recommendations and looking for that ‘stroker rumble’ not looking to put so much into it...

looking for a set of wheel well trim - so cal pick up preferred to save on shipping but let me know what you guys might have. thanks .

Hello Everybody long time, 1968 Plymouth barracuda Notchaback i am looking for a shop to do my head liner in orange county (Socal) area. would appreciate any help.

RECENTLY installed an intake riser 1968 barracuda notch - 1973 charger 440 STOCK cable is okay and long enough but issue is with the tie down cable bracket which allows only for certain amount of slack & need a higher bracket for the throttle to be fully seated and closed ... anyone have any...

any one know what the white plastic washer holders for the steering column are called and where i could get them? the hold the column part that cradles the actual column. there are two of them possibly three. is square looking with two notches

STEERING U-JOINT 1968 barracuda notch 1973 RB 440 727 trans - 8 3/4 rear end power steering power brakes (disc front drums rear) steering box ???? unable to get numbers off of it (tight squeeze) stock everything - Okay so the last time i attempted this i tried about two or three different...

HELLO, guys i think i have asked before but couldn't find any evidence that i had. I am looking to replace my brake booster and master cylinder on my 1968 plymouth barracuda (not original or original owner.) it has power steering - front disks rear drums - with a dodge 440- i am browsing around...

Not sure if i mentioned to all you guys that live in So CAL. I work for a Lubricants company i can get most oils, coolants and race fuel and propane at cost. if anyone ever needs. just shoot a PM

i have a 1968 plymouth barracuda with a 8 3/4 rear end big bolt pattern. my question is... What drum brake pads would i need to buy? are there different ones? :coffee2::burnout:

Driveline shop in Placentia California info: Address: 471 Industrial Way, Placentia, CA 92870 Phone:(714) 993-6494 Just wanted to get them out there for anyone in SOCal.WITH DRIVE SHAFT needs ***** (five star extremely satisfied) These guys did a great job building me a brand new drive...

1968 plymouth barracuda 440 8 3/4 rear (SUREGRIP) i recently started to drive my Barracuda (daily driver) work and back home about 20 miles round trip daily and started to notice the vibration. recently did the SS suspension on it and thinking the angle might be off but took a quick look...

i have a 1968 barracuda 440 8 3/4 rear 727 trans. when going from drive to reverse and the other way around its a bit ' jerky ' ' noisy ' in my opinion not much but its there a bit bothersome. :blob: would this be something with the transmission or the rear end or drive shaft?

1965 AMC Rambler - pick-your-part Anaheim California

1968 barracuda 440 magnum off of a charger. power steering front 73 A-body disc brakes. not sure what K-member i have .... my question is, NEW motor mounts which to get. to match the motor? to match the k-member? to match the car?

i have a 1968 barracuda notch. power steering and front disc brakes. 1972-1973 440 magnum off of a dodge charger. what headers do i get? obviously big block 440 headers but A-body to match car or B-E body to match motor? and would they both fit...

Hey guys I have a 1968 barracuda w.1972 or 1973 440 magnum stock exhaust manifolds - I need an extra long set of wires to be able to route these things out of the way of the already tight fit from this big motor. Suggestions?

i am getting ready to do some prep work for paint i will start removing all trim and chrome from my 1968 barracuda NOTCH. any advice from people on how to remove trim or maybe some advice on things "issues" people have run into before when removing trim and chrome. originally a vinyl top...

I've seen her around and finally caught her standing still with enough time for me to take a photo. Any one recognize this one? :coffee2:California car. Down town Brea.

My son and I occasionally work on the Barracuda want him to get a sense of the Mopar/Car scene and father son activities are a plus right. So this Last Fathers day he gave me two neat things. One - The key to my very own Daytona Superbird. Sweet! Two - A windshield Sun visor with...

i was recently in the junk yard and saw a DODGE VAN with a V8 and noticed that it had a pretty much "NEW" shinny HOlley carburetor compared to the old oily motor. my question is - DO these carbs come in these VANS or should i get my @$$ over there and get this before some one else does...

Pick your part -Anaheim California :cheers:

Ecology - La habra California

Well guys i have here a - 1968 Plymouth Barracuda Notch-back. (clean title) 440 727 8 3/4 rear. New front & rear end suspension build. Everything else pretty straight forward. Fender tag- though not sure what this E8 code is E8 didnt work E0 didnt work E3 didnt work. i will clean it up and...

Hmm looks like Barracuda Stock will be rising soon? :burnout: i don't know about everyone else but the Cuda' was always 100 times better than the whole challenger series . . . :blob:

was driving my barracuda brought it up to TEMP. and i started to smell hot/burned antifreeze coolant popped the hood and noticed the top hose was hard and semi "ballooned" did i over fill my radiator with coolant? is my thermostat not opening? gauge doesn't show overheating holds at 190' which...

any one ever used this service? if so does anyone have any feedback or advice? :coffee2::burnout: they have my paint poly blue 13445 - cant wait till i get it. :happy1:

im looking into spraying my car myself - try it out to see how it goes.... any one car suggest where i could find Chrysler paints? and or procedures in doing this? step by step .... :blob: