Search results for query: *

I just redone my 340 . and had great oil pressure 80 +lbs. new hv melling pump and deep pan. drove it a few times its ok . went for a cruise and its all over the place from 0 to 30 get it home change oil from break in stuff . now only have 40 to 45 lbs and when you raise rpms pressure goes...

i am rebuilding my 340 that has rpm heads and crane rockers they are a older set, i am going from a flat tappet to roller. do i need to upgrade the shafts to the better oilers, and i have the stock hold downs do i need to upgrade them to the better ones for alumn. as hughes recommends?

does any body run the stock windge tray and a moroso pan? i had to cut it for pickup and i cant run the nut under tray beween cap and pan on arp studs or tray hits oil pan, should you run a tray with the moroso pan? it fits now but it is tight. pan no. 20710

building a +030 340 11.1 rpm heads, need a balancer whats everyone using? anyone try the fluidampers on ebay? Ideas?

71 scamp 3300lbs street/strip, 340 +.03 11.6-1 stock stroke, scat h-beam, ross piston measured cc to get comp. edelbrock heads 2.05/1.6 fully ported, flow [email protected] in [email protected] and [email protected] ex, [email protected] cam soild roller lunati voodoo #60434 .600/.600 255/[email protected] dur 110/104 lsa/lcl cam holley...

i bought a new set of main bearings for my 340. they are clevite p bearings and they have a full groove top and bottom. they just package 2 uppers in the box. no 1,2, and 4 mains. thrust and rear still std. will this cause any problems or will it give better oiling? called clevite and they say...

Looking to replace my stock rods what do you guys recommend? 500 to 600 hp limited nos shot up to 175hp. under 7500 rpm

If you had a 340 block and wanted to do a stroker kit who's and what cu.in would you pick? would be a street/strip combo 11 to 1 3400 lbs car.

I have a chance to buy a 3.79 stroke crank and .040 over pistons for my 340 .03 motor will make it a 396 this will be a flat top compared to my 11 .1 dome what you guys think? will it pick up with less compression? also was told this a mopar crank made by callies anyone heard this?

I need a balancer for my 340 and was wondeing what you guys think of the fluidamper from KMJ. would like sfi. one i spin it to 7200. I know ati is the way to go but to pricey for me.

I am putting a soild roller roller in my 340 and would like to know who's lifters everybody is using and why?

I am building my 340 up and would like to change intakes. have holley strip dom. on it know wnat to go vic. 340 or super vic.which one do you guys recommend and why? combo is 71 scamp 344 cu 11.6 comp.eddy rpm heads full ported. putting in 2.08 valve. soild roller .665 lift 258/262 dur. 108 lc...

i want to switch out my 727 for a 904. how do i id it? was told get a low gear one and does th 6cyl. one fit a small block?

I have a victor 340 intake and would like to get it ported. Who are you guys using and do they flow it or just know there stuff? flow it on head?

I want to install a soild roller cam in my 340 and wonder how many guys run them and what issues you may have with them.

I have a set of edlbrock rpm heads on my 340 that where ported by hensley 15yrs ago would like to see if these can be improved. Who would you guys send them too? also would like to get a intake ported to match. have a holley strip dom .i have been running also have a victor 340 wich is better...