Search results for query: *

PG classic has the linkage on sale right now ! FYI

68 dart 73 and up spindles

So i asume that with these control arms you can interchange from small to large without any fitment issues?

Hey there i bought these control arms for my dart project , the castle nut had 2 spacers under it. Not sure what the spacers are for,when installing the ball joint into the spindle the taper bottoms into the spindle but it also cuts the grease boot. So i asume that one of the spacers goes on...

Thanks for the info, will have to change the way its set up

The way it is now , i have a small pc of hose with a air line vent on it. When we fill the tank gas pours out of this vent , without putting a charcol canister up front and running a other line to front ,run it to the filler neck, car has a vented cap should work ? Not sure lol,any thoughts

Turns out its a pump issue, were gonna install an electric pump some where lol . Anyone have install pics of where they intalled their pumps? The vent at the top of the tank we are gonna runn a hose to the top of filler neck and tie into that hopefully cures a few things

Vehicle shuts off during initial warm up , cant even get it out of driveway, we changed sender last night , we have the later tank with the eec emissions that port at the top of the tank is that a vent or is that for charcoal canister ?

Car was built 2 yrs ago was a new tank and sender at that time , problably gonna pull sender and see if any issues

Son's demon has a gas tank that has a vent atthe top of the tank and the sender has 3/8"inlet , there is a second line there i beleive 5/16 "dia. Where do we hook the 5/16 line to ?or do i block it off? We are having fuel delivery issues with this car , starts and runs then stalls and then no...

So there is no factory vent lines under the car i think at one time it had the factory evac vent but don't know what to do with this line ??? if I plug it will it create a fuel delivery issue ??

We're building a 71 demon just put the new tank and sender in 3/8 line to carb , where does the other line go to ??? Any help would be great Thanks Mike

If anyone has this stripe on the hood of there car can they measure how wide the stripes are on the side of the hood ,????

Had to ask you never know

Ya I knew about the stencils, was hoping some one would have a detailed drawing so we could freehand the stripes lol

Was wondering if anyone has and layout drawing for the stripes on the hood as per pic any help would be great Thanks mike

Not sure how to delete lol , but its all good no worries. As far as the starting thing it could be a lot of things , make sure you have spark , could be a faulty control box if it has electronic ignition

Click on new post at the top of page and begin

Have 66 383 was gonna order a torque converter for the 727 trans ,2500 stall , now this motor is internally balanced , steel crank motor ? So I should get an unbalanced or balanced converter?? Any help would be great Thanks Mike

So building a 383 for our demon it will be .040 over , 66 block , 452 casting 440 heads we are trying to decide what kinda cam to use for this application? We are looking at this comp cam package k21_224_4 was wondering if anyone has used this camshaft kit ?? What the drivableabilty would be...

So we have a 72 demon were trying to hook up park brake , it has 2 short cable off the diff, one long cable that hooks to the front cable and both back cables . So where does the hook bolt hook to on the passenger side?? Does anyone have any pictures of this ? Thanks Mike

So we have a B body axle in my son's 71 demon we finished off the brakes and put the wheels on figured we were done. I grabbed the wheel top and bottom checked for wheel bearing play , found to be a lot of play on both sides , is this adjustable or are the bearings done and need to be replaced...

so this the cam I'm using , heads have 202 valves , stock bottom end 318 ,with windage tray !!

So I'm building this 318 , 1987 block , 340 heads and manifolds, I have two intakes to choose frome one is a holley street dominator (small ports 318),the other is the factory 1977 cast 4 barrel intake (large ports). So I'm thinking cast one would be better because of larger ports? But never...

So building a 318 for my 67 barrcuda and was gonna paint the motor red , is there a paint code for the red on the engines in 67/68 ??? Went to the parts store for paint couldn't find any Chrysler red color?? Any help would be great Thanks Mike

No the cam bolts we junk had to torch them off Mike

So went the wrecker yard today got the control arms 85 bucks last pair there Thanks for the help on this Mike

So it won't mater if the drums are small or large bolt pattern? ? Should be the large ball joint ?? Thanks Mike

So was at the wrecker yard the other day and there was a dart there with drum brakes on it . I checked for Vin # but the dash was gone , so can't verify the year , I have a picture of the body tag I think it's a 74 ! Would those control arms be the ones I want for a 73 and up disk brake...

Bought a windage tray/came with hardware 4 main cap bolts ,8 washers and small attaching bolts , never installed one of these on a small block before ,so I assume you stack 2 washers on each main cap bolt ???? Thanks Mike