Search results for query: *

Looking for some info on flexplate vs torque converter combinations. Presently have a B&M 10237 flexplate married to a 3000 stall converter, 440 has cast crank ( rotating assembly has been balanced) as well as 727 has been rebuilt. Getting a vibration in reverse/ forward that follows rpm 1000-...

Hello , I've got a small leak that is gravitating to just below the speedo gear so pulled the speedo gear assy ( has brand new seals on it , inside & out) and put tiny slick of gasket sealer on oring then reassembled, thinking that might be it. Wondering if can be coming from somewhere else ...

I have a 1969 dart with a 440 and a 3 row aluminum radiator, does anyone have this same setup ? And what fan / spacer would you recommend? It has 2 1/4" from the fins to the face of the water pump pulley fyi.

Just fishing for constructive thoughts/ advice on fuel lines / pump proximity to exhaust ? I've seen various pictures of different setups and I'm still looking for more examples.

Hello I'm looking for a quality piece of trim that holds the carpet in place and attaches to door sill trim RH . At the base of rear seat. LH Pics for reference.

Not sure if the squirrels ran off with or ate the rear window crank shim/ gaskets ( just pulled box out of my shed ) but does anyone know if the 69 dart came with those ?

Rear window rubber question for 1969dodgedart, there's a flap of window rubber that looks like it sits on top of pkg tray when its installed? Just wondering where it sits.

Just a heads up to the A body mopar grp. Had a bad experience with PG classics over a defective steering wheel and want to make everyone aware . Bought a new steering wheel from PG last spring and just put power to the car, the horn stays on . Did some continuity tests and found the horn contact...

I have a 1969 dart and I'm looking for information to set orientation of the signal trip mech on the back side of the steering wheel? Sits under the horn contact ring . Thx

Recently bought some oe replacement wiper blades for my 1969 Dart and I am on the hunt for picture of how they attach to the factory arms? Thx in advance.

Looking for a RH headlight bucket for a 1969 Dart .

The person that owned this car before me had it apart and butchered when I bought it fyi .Just throwing this out there looking for some information and possibly pictures/ diagrams. I'll start out by saying I have some wiring diagrams printed off for reference but they aren't great. There's three...

Looking for a picture of starter wire routing to the starter itself. Even a factory v8 picture . 1969dodgedart . Thx

Looking for a picture of license plate light installed showing the orientation of the lens and the socket ? This is for a 69 Dart. Thx

Bought a retrosound Redondo to put in my 1969 Dart , having a brutal time assembling so it will fit the factory face plate and fit in the dash . Anyone with any tips or suggestions?

Looking for a picture of hood release cable routing with firewall hole location? 1969 Dodge Dart.

I'm looking for picture or diagram of brake / fuel line clip positions/ orientation for 1969 dart ? The pictures i took before disassembly aren't cutting it . Thx in advance.

I'm looking for suggestions for full length 3" exhaust coming out under the bumper ? 440 with 727 , tti headers .

Looking for parts listed: -Wiper switch knob -Heat control slide knob -Spare tire board plastic hold down -Both sun visors/ black in good condition with brackets - jack / jack foot / jack attachment for bumper - Lh A pillar windshield chrome - rh original taillight lense with inner...

Just trolling for information and ideas on incorporating two electrical items into my car ie: stereo ( amp etc ) / electric fans ? Already have a plan just want to see what other thoughts are out there .

Just fishing for some opinions on engine movements/ radius shake . How much movement would there be with a 440 with Schumacher mounts ? I'm trying to place my Lokar trans dipstick grab end to the firewall and want to make there is enough slack for movement. Thx

Looking for solutions on this issue , I'm mounting a temp sensor for electric fans and aftermarket gauge cluster as well as the factory gauge . Any ideas and pictures? For a 1969 dart. Thx

Does anyone have a picture of the wire routing for fuel sender in the inside of the trunk for 1969 dart ?

I've got a problem with not enough gas pedal / cable travel . When the cable is attached to pin on the carb at idle position with no play and then you press the pedal down to the floor its not fully opening the carb butterflies . Seems like it needs another 1/2" of travel on the cable/ pedal ...

Looking for photos of underbody/ firewall for reassembly .

I,m looking for photos of Dart underbody and firewall for reassembly guide . Thx

Does anyone have any suggestions for a shop that would do the final sand and put the paint on my 69 dart ? In the central Ontario area / Barrie.

Looking for a reputable autobody shop or private small shop to finish my Dart in central Ontario, Canada ( Barrie area )? Been thru a few playing the waiting game that have fell thru. Waiting 2 years as of September, frustrated to say the least .

I'm presently wrestling with trying to figure out a solution for a spare tire/rim I can use front / rear and fits in tire well. This car has 18" x 8 " wide rims front , 19" x 10 " rear with ECI brake kit on the front . So far all I can find that will fit front/ rear wheels and fit in the spare...

Does anyone have pictures of a holley electric fuel pump mounting configuration on a 1969 Dart ? Looking for ideas. Thx